Jump to content
SAU Community

Recommended Posts

sounds allot like the master cylinders is gone finito caput lolz. but could be brake booster as well but master should be the problem that is from experience. but can never hurt to be check by a professional and get this problem fixed asap or else it will happen again and it can be scary if that happens where no brake power and u going down a hill thats from experience and hope no one experiences that lolz

nah shouldn't lol any pro can diagnose it , i just got miy brake master reconditions and doing full brake make over for my 32gtst lolz befor road use !! its good to search whats good and whats not :D

This sort of saves me making another thread, so i'll semi- hijack yours

I have a gtr with standard rotors, (well standard spec, not slotted or anything tho) and some high performance pad (i saw them in a catalogue and they're quite exxy green ones)

Anyways after doing a few spur run's i locked up the brakes a lil coming into a corner and had the abs light come on, it braked fine but about 10 minutes later when i stopped at some lights i could push my pedal all the way to the floor, and pumping didn't really work. By the time i had gotten home the problem had almost gone and now when i drive it it brakes fine but it doesn't seem as responsive.

More effort is needed to brake (it still brakes easily enough) and my corolla and val both brake alot easier than the gtr. I can't really remember how it was before you but considering the size of the brakes i'm guessing they're normally alot more responsive.

It has plenty of fluid and i only bled the brakes about 1500 km's ago, i'm thinking maybe the diaphragm is gone but i'm not sure, maybe gtr's have a bit of take up b4 they break standard.

Also 1 other thing, idk if it's bad but it never happened in my old car, my brakes smoke a fair bit after a hard-ish run, they don't smell oddly enough at all but they smoke a fair bit

Ne ways, no idea about the 2nd bit but does the 1st problem sound like master cylinder is shot?

I think you've boiled the fluid. Some liquid or air might have got in there. Bleed the brakes again and that should fix it for now but if it happens again then look to the master cylinder. It's not the booster.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Yeah, I don't believe the M35 uses a deadhead system.
    • Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...