Jump to content
SAU Community

Clutch Fluid Reservior Location

mark_sudakov

By mark_sudakov,
in General Maintenance

 Share

Recommended Posts

mark_sudakov Community Regular

mark_sudakov

Posted
Posted

Hey,

This may be a stupid question, but is the clutch fluid reservior the little white one closest to the firewall on the left side of the engine bay? Just want to double check before i fill it up as its quite low.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/198049-clutch-fluid-reservior-location/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

yep thats the clutch.

edit: sorry to clarify the clutch is on the right as you look at the engine, brakes are the larger one on the left.

and clutch fluid should not be getting out so you might have a stuffed slave cylinder or master cylinder seals.

mark_sudakov Community Regular

mark_sudakov

Posted
  • Author
Posted
yep thats the clutch.

edit: sorry to clarify the clutch is on the right as you look at the engine, brakes are the larger one on the left.

and clutch fluid should not be getting out so you might have a stuffed slave cylinder or master cylinder seals.

thanx for the quick reply.

I dont seem to have any leaks anywhere. Seems like i should investigate this further

mark_sudakov Community Regular

mark_sudakov

Posted
  • Author
Posted

just a little confused, both clutch and brake fluid r on the left of the engine bay, correct? But the clutch fluid reservior is closest to the firewall than the brake one?

Duncan Grand Master

Duncan

Posted
Posted

lol I'm not explaining this well am I?

brakes are large and on the left. clutch is small and on the right. both are attached directly to the firewall (wall between engine bay and cabin)

brake fluid can get low as the pads wear and will come back up when you put new pads in

clutch fluid should not get low

Duncan Grand Master

Duncan

Posted
Posted

well thats hard to tell unless you can see signs of fluid leaking.

Firstly fill it back up and keep an eye on it. Have you noticed any problems engaging the clutch?

If its leaking at the slave cylinder you can get aftermarket ones easy. Master cylinder you may need to buy a new assembly, not sure if there is an aftermarket alternative

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • MBS206
      spot the stagea

      By MBS206 · Posted

      It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...