Jump to content
SAU Community

Recommended Posts

Hey There,

Got my new engine put in this week, and after a bit of driving around etc i've noticed that sometimes when the revs are low and building up to boost

at about 2500rpm the car stutters a bit and feels like its holding back, then once it gets past there it boogies.

Now, i had a major issue with one of the cams f**king up so one of my old cams was used in the motor as the other was broken, now if the cams were say to be different would this cause the issue? The cams supposably on the new engine were NA ones but im unsure of this as a fact.

The car doesnt really pull hard on 14psi as it used to, it used to throw you back in your seat now the car just seems to pull along the revs?

Also thinking Injectors or fuel pump?

Help! I wanna get this fixed!

Trent

oh ok sorry - so the engine was just put back in the car?

id say something is loose, like a hose clamp, intercooler pipe work, the air vac lines for the actuator etc - something along those lines?

Well its not the gap on the plugs

After a fair bit of reading ive come to the conclusion that its the fuel pump not sending enough to the engine, probably causing it to lean out. The car runs fine when cold but thats when its running rich but as soon as it settles its stuffed.

"Many of you with S13s have probably experienced hesitation on boost which can start to happen when the standard fuel pump is getting old."

I believe thats what my problem is.

Now im estimating that its dangerous to drive the car whilst in this state, i.e fuel pump could break down, or could lean the engine out.

Would i be right saying that?

it will be dangerous for you to give the motor any reason to demand more fuel yes.. like cracked piston spec. putting around not so much the best thing for you to do man is take it to a dyno and get your air/fuel checked out they will be able to tell u if it is leaning out or not, if so extreemly likely tis the fuel pump

what gap and how much boost are you running? I was running 14 psi and I had a stutter even after I put in a new 040 pump and pulled the gap from 1.1 to .8 and it stopped it

Edited by BANGN
  • 2 weeks later...

Car was datalogged today, we found that the timing was out. We also adjusted the teeth so that it was sitting perfectly.

We also changed over to a working CAS which still didnt fix the problem, the timing was jumping around from sitting on 15 to 7/8 up and down. Also tried a few diff coilpacks but we are unsure if they are working correctly.

I'm waiting on my walbro replacement to come back then ill be installing that into the tank see if that fixes the issue, other than that its coil packs/injectors we are thinking.

Anyone able to add some to the situation?

Also, if somone could be nice enuff who lives in the melbournes west to let me borrow there coilpacks for 2 minutes to see if the car runs any better would be appreciated.

For a 180sx SR20 Red Top

Anyone who can help either post or pm me please!

My car does the same sometimes, most likely cause would be either fuel pump or injectors. i have a power fc and when it happens i look at the inj duty and its 100% . It never used to it when i had 550cc in there. Two ways to fix it....

1. Bigger fuel pump, Fuel reg and bigger Injectors and tune.. or

2. Turn the boost down.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...