Jump to content
SAU Community

Recommended Posts

Hi All,

Unfortunately (for myself) I am selling my pride and joy, my R32 Skyline. Allot of time effort and money has gone towards this car and it is defiantly a great every day drive as well as a very quick car. The car has always been taken care of and serviced regularly with top of the range full Synph oil and has always been tuned at Croydon Racing in Silverwater, last tune it got 253kw at the rear wheels (so not for the faint hearted).

Due to the amount of mods/power that this car has absolutely no joy riders allowed

This is a very regretful sale but car needs to be sold . The details for the car are as follows:

Make: Nissan

Model: R32 GTS-t type M

Milage: 92,000km

Transmission: Manuel

Colour: Black

Location: Sydney NSW

Complied? Yes

Currently registered? Yes

Price: AU$14,000 ono

Contact: Bruno on 0404088191

Comments / Modifications:

* HKS Type S Intercooler

* 650cc SARD injectors

* Garrett 30/37R Ball Bearing (T3/T4 equivilent)

* Tomei Poncam Cams

* Apexi Power FC (Re- Tuned)

* AVC-R Electronic Boost Controller

* HKS Air Pod

* Z32 Air Flow Meter

*Custom made Top mount Manifold

* 38mm External Wastegate

*Number Plates "FST32R" to be sold with vechile

Images: post-46198-1199616751_thumb.jpg post-46198-1199616829_thumb.jpg post-46198-1199617973_thumb.jpg post-46198-1199620471_thumb.jpg

post-46198-1199620739.jpg

Edited by Zav

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...