Jump to content
SAU Community

Recommended Posts

Ok, had a stutter and felt like the car was holding back around the 4500 rpm mark which after alot of reading seemed the coil packs where to blame and a test would be a good idea,

Tested the ones in my car and they all read 1.1 ohms, strange? Was looking for around 0.6 - 0.9, correct? I thought there might be a bit of difference in them so i tested ones out of another engine and again all where 1.1 ohms, even stranger? so i tested a load more and was getting the same reading for all of them!

Then warmed up my original ones and tested them again, this time they all read 1.3 ohms? So in therey, after all the reading these should all be f**ked, but surely this can not be the case?

Im using a multimeter set on 200 ohms, addmitidly the meter is a bit s**t, maybe this is the problem? Im testing them out of the car hot and cold and on the + and - pins, is there something else im forgetting to do, the way im doing it i belive im testing the primary coils and also how to you test the secondary coils?

Can anyone shed any light without the reply of get yourself some splitfires, thanks again..........

Link to comment
https://www.sau.com.au/forums/topic/202253-coil-packs/
Share on other sites

  • 3 weeks later...
Can anyone shed any light without the reply of get yourself some splitfires, thanks again..........

G`DAY `LOZ, If you have a look in this section you will find :D ,I did have some problem`s with my coilpack`s :P but no more,SO LOOK AT REVOLUTIONARY FIX`S :P ,GOOD LUCK,cheer`s chuckiepost-36964-1202221551_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/202253-coil-packs/#findComment-3626643
Share on other sites

If u have an aftermarket ecu u can increase the dwell times. This will fire your coilpacks for longer and ensure a good spark. Increasing it also reduces its life.

You can also reduce the spark plug gap to 0.8mm to reduce misfire brought on by shite coilpacks

Edited by Jmaac
Link to comment
https://www.sau.com.au/forums/topic/202253-coil-packs/#findComment-3642920
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...