Jump to content
SAU Community

Recommended Posts

For sale:

RB26dett built about 2 years ago by benny at hi torque but built just previous to hi torque.

engine has full new crank

forged pistons

big cams

garrrett 2560r turbos

n1 pumps

modified ignition

ported head

metal head gasket

head stud bolts tomei

ehxasust manifolds

makes easy 350kw at all four wheels on pump fuel all day

all receits for the engine build nearly $20,000 for the build alone

also comes with apexi power fc

and excceedy triple plate clutch valued another $3000.

This packagae is a cheaper and easier solution for anyone wanting more power i have all photos of the build

and the engine is currently in the car

reason for sale is simple RB32 is planned.

the plan is to sell the entire package as is leaving the bottom diff / sump in the car.

GREAT VALUE.........

i also have an N1 block for sale brand new. make and offer.

all enquiries please call 0405385519 or email [email protected] for photos coming soon.

Attached thumbnail(s)14000, ONO

or

15k with clutch and fc

ONO.

post-9341-1200824781_thumb.jpg

post-9341-1200824787_thumb.jpg

post-9341-1200824795_thumb.jpg

post-9341-1200824801_thumb.jpg

post-9341-1200824806_thumb.jpg

post-9341-1200824812_thumb.jpg

Edited by tribex

Where did you get engine ported?

what was the before an after port bench flow test results?

Is the valve train still standard OEM items?

What rods and what rod bearings did you use?

What big end bearings etc did you use in build?

cheers mate...

Also what gaskets did you use in build?

Where did you get engine ported?

what was the before an after port bench flow test results?

Is the valve train still standard OEM items?

What rods and what rod bearings did you use?

What big end bearings etc did you use in build?

cheers mate...

Also what gaskets did you use in build?

cp forged pistons

rev conrods

new crank at time of rebuild

cp rings

ACL race bearings

main stud kit

head stud kit

tomei steel head gasket

tomei poncams

tomei valve springs

tomei camgears

genuine gaskets and seals

trust exhaust manifolds

trust dump pipes

garrett -8 ball bearing turbos

sard 800cc injectors

fuel pressure regulator

gates race timing belt

n1 oil pump

n1 water pump

tomei sump baffle

blue printed and balanced

professionally assembled

engine currently makes 630hp (340kw at all four wheels)

can handle over 700hp with larger turbos

tripple plate exedy clutch

power fc

plus heaps more i probably havent listed!!!!

post-9341-1200897485_thumb.jpg

Edited by tribex
how mch mate, whast the price you are after????

i think the entire package 14000 ono. consider the build and parts alone over 20k and a standard good engine out of a late model 33 '97 would cost maybe 5k for the engine alone.

taking offers.....

i think the entire package 14000 ono. consider the build and parts alone over 20k and a standard good engine out of a late model 33 '97 would cost maybe 5k for the engine alone.

taking offers.....

wowww......... that is bloody cheap, anywayone got a r32 gtr shell can spend another 15gz insetad of spending 25gz and get this entire mostrer package,

mate if i had a no engine in my gtr i would of ran for it,

gl wid sale, free BUMPPPPP

wowww......... that is bloody cheap, anywayone got a r32 gtr shell can spend another 15gz insetad of spending 25gz and get this entire mostrer package,

mate if i had a no engine in my gtr i would of ran for it,

gl wid sale, free BUMPPPPP

bump dont want to seperate may consider offers without turbos

pms sent

Generally helps to put it in your first post... using the pre-format thats given.

Hence it makes it clear for users/Admin alike.

DONE in first section thanks bump.

PS will not sell turbos until engine is sold if its sold without them thanks guys.

hey mate, interested in just the botom end and dont need the head or turbos, would seprate ? and how much u after ?

not really buddy i might sepearte the engine and the turbos and clucth and fc but i dont think i want toll the bottom end.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...