Jump to content
SAU Community

Recommended Posts

I need some help figuring this out.

I have the R34 GTT vented fenders and they are 20mm wider than normal. I'm trying to order the Racing Hart CXR's.

Front 19x8.5

Rear 19x9.5

On the racing hart website it says the offsets for a R34 25GTT are...

Front 18x8.0 +35

Rear 18x9.0 +38

I have no idea if that means they are flush or not.

I'm looking to have my rims fitted flush with the guards... so what offsets should I use if I'm going 19 inch rims 8.5's and 9.5's? Any help would be appreciated. Thanks!

Hey mate, try using this calculator:

http://www.1010tires.com/WheelOffsetCalculator.asp

Type in your current wheels, after market wheels and you'll see how much more/less they stick in/out. Just keep playing till you get something you like then go out hunting for them wheels! :)

Good luck with your search, anymore questions, feel free to ask.

Hey mate, try using this calculator:

http://www.1010tires.com/WheelOffsetCalculator.asp

Type in your current wheels, after market wheels and you'll see how much more/less they stick in/out. Just keep playing till you get something you like then go out hunting for them wheels! :worship:

Good luck with your search, anymore questions, feel free to ask.

Thanks adam but I've seen that before. I can't use it because I don't know what the specs are for stock R34 GTT rims and the stock GTT rims don't sit flush. Also, I'm getting new front vented fenders that are 20mm wider than stock. Does that mean I subtract 20mm from the front offset? For example, if my front was 19x8.5 and offset was +30 with the stock fenders then I would need to find +10 offset rims if I get the vented fenders. I don't know how that works.... do I need 225 on the front to make clearance or will 235's or 245's be ok? Would 265's be alright for the rear on 9.5's?

Edited by chak8080

Lets just say your standard wheels are 6.5" wide and have an offset of +40 (not sure what they really are, but just going with standard r32 wheels). At the moment they are IN the standard guards by lets say 20mm. To have the wheels flush with the standard guard, you'll need wheels which are 6.5" wide and with an offset of +20, 8" wide with an offset of +39, etc. But since you're having the wider guards, you'll need 6.5" with a 0 offset for them to be flush, 8" wide with a +19, etc.

Remember that this is for your wheels themselves to be flush, with the guards, not tyres. Having tyres will make the 'package' stick out a little more if you're not planning on stretching some tyres.

Hope that helps... at least a bit. haha

Lets just say your standard wheels are 6.5" wide and have an offset of +40 (not sure what they really are, but just going with standard r32 wheels). At the moment they are IN the standard guards by lets say 20mm. To have the wheels flush with the standard guard, you'll need wheels which are 6.5" wide and with an offset of +20, 8" wide with an offset of +39, etc. But since you're having the wider guards, you'll need 6.5" with a 0 offset for them to be flush, 8" wide with a +19, etc.

Remember that this is for your wheels themselves to be flush, with the guards, not tyres. Having tyres will make the 'package' stick out a little more if you're not planning on stretching some tyres.

Hope that helps... at least a bit. haha

Ok, so what your saying is that an increase of 1.5 inch on the width of the rim equates to +19mm (38mm/2)?.. in respect to that an increase of 0.5 inch would equate to +6mm (12mm or 13mm/2)?

I read somewhere on SAU that says the following is the best set up for a R34 GTT(i don't know if this is for a 2Dr or 4Dr).. Rims sit flush..

Front 8.5 +32 offset 225 tires

Rear 9.5 +38/35 offset 265 tires

If that's the case then I can use this as a base. Since my front fenders are going to be 20mm wider would this be right..

Front 8.5 +12 offset 225 tires or 9.0 +18 offset 225 tires

Rear 9.5 +35 offset 265 tires

Would that make the front flush again?

Does anyone have a ER34 GTT 2Dr that's running 19x8.5 19x9.5?

Edited by chak8080
I need some help figuring this out.

I have the R34 GTT vented fenders and they are 20mm wider than normal. I'm trying to order the Racing Hart CXR's.

Front 19x8.5

Rear 19x9.5

On the racing hart website it says the offsets for a R34 25GTT are...

Front 18x8.0 +35

Rear 18x9.0 +38

I have no idea if that means they are flush or not.

I'm looking to have my rims fitted flush with the guards... so what offsets should I use if I'm going 19 inch rims 8.5's and 9.5's? Any help would be appreciated. Thanks!

To match 18x9.5 +38, you will probably then need 18*9 +12 with those extended guards to sit flush?

Ok, so what your saying is that an increase of 1.5 inch on the width of the rim equates to +19mm (38mm/2)?.. in respect to that an increase of 0.5 inch would equate to +6mm (12mm or 13mm/2)?

I read somewhere on SAU that says the following is the best set up for a R34 GTT(i don't know if this is for a 2Dr or 4Dr).. Rims sit flush..

Front 8.5 +32 offset 225 tires

Rear 9.5 +38/35 offset 265 tires

If that's the case then I can use this as a base. Since my front fenders are going to be 20mm wider would this be right..

Front 8.5 +12 offset 225 tires or 9.0 +18 offset 225 tires

Rear 9.5 +35 offset 265 tires

Would that make the front flush again?

Does anyone have a ER34 GTT 2Dr that's running 19x8.5 19x9.5?

Yes, as far as I know, that should be correct.

To match 18x9.5 +38, you will probably then need 18*9 +12 with those extended guards to sit flush?

18x9.5 with +38 will sit in the same position as the 18x9's with +12.

i dont have 19s but ive got weds 17 with 9 front, 9.5 rear, and +35 offset allround, and they look shmick and tucked nice under the

guards

Do you have any pics?

Yes, as far as I know, that should be correct.

Ok, I thought I had it but now it's getting confusing... If I go off of Racing Harts website it should come out to this..

Front 18x8.0 +35 to 19x8.5 +29 (-6mm for 0.5 increase in rim width) to 19x8.5 +9 (-20mm to bring the dish out to fit flush with the 20mm wider fenders)

Rear 18x9.0 +38 to 19x9.5 +32 (-6mm for 0.5 increase in rim width)

Should I leave like 3mm or so clearance to maintain my turning ability? I want my tires to be slightly tucked so the rims don't hav eto sit perfectly flush... just flush enough where it looks 'full'.

jesus... I never knew sizing rims could be this difficult. It would be nice if they sold my PCD here in Korea so I can do test fits... but since I can't I don't want to waste money sending rims to and from Japan until I get the right fitment... these rims are expensive enough!

Does anyone know the stock setup for a 2Dr R34 GTT? I think the rims are 17x7.0 all around and +30/35 offset all around?? Someone correct me please.

Edited by chak8080

I agree, wheels are expensive and you want to do it right the first time.

With the troubles turning, it would really depend on how low your car is and how stiff your suspension is.

'Flush' for you could mean tucked for me. Can you get a picture of where you would like your wheels to sit? Cause when I say 'flush' I'm thinking...

post-32186-1201765940_thumb.jpg post-32186-1201765960_thumb.jpg

R34GTT standard wheel specs are 17x7.5 +40

Use that as a base when using the wheel offset calculator.

2dr and 4dr use the same specs. I have run 8.5 and 9.5 +35 all round and still have a bit more room to move...say 5-10mm

If you are running wider guards +20mm then subtract that from what is recommended...I would personally be a bit more conservative and maybe subtract 15mm instead of 20mm...

With those guards you should be able to run 350z or even GTR offsets (have nice dish!)...approximately

8.5 +15

9.5 +20

Best to get your guards on first so you can measure how much room you have to play with based on the wheels you have on now...

If you need some ideas of suitable offsets for stock guards, have a look at my collection >_< Click on the archived months as well.

http://www.n15m0.blogspot.com

R34GTT standard wheel specs are 17x7.5 +40

Use that as a base when using the wheel offset calculator.

2dr and 4dr use the same specs. I have run 8.5 and 9.5 +35 all round and still have a bit more room to move...say 5-10mm

If you are running wider guards +20mm then subtract that from what is recommended...I would personally be a bit more conservative and maybe subtract 15mm instead of 20mm...

With those guards you should be able to run 350z or even GTR offsets (have nice dish!)...approximately

8.5 +15

9.5 +20

Best to get your guards on first so you can measure how much room you have to play with based on the wheels you have on now...

If you need some ideas of suitable offsets for stock guards, have a look at my collection :D Click on the archived months as well.

http://www.n15m0.blogspot.com

Hey thanks n15m0! Thats what I was looking for.

I agree, wheels are expensive and you want to do it right the first time.

With the troubles turning, it would really depend on how low your car is and how stiff your suspension is.

'Flush' for you could mean tucked for me. Can you get a picture of where you would like your wheels to sit? Cause when I say 'flush' I'm thinking...

post-32186-1201765940_thumb.jpg post-32186-1201765960_thumb.jpg

Nice! That's what I mean by flush too butI don't know if I'll rub or not from getting the wrong tire size. I don't want to strech them too much. So either I'll go with the strech or I'll just have the rims tucked a bit more.

Ok guys, this is what I'm going with.

Racing Hart Type CXR

Front 19x8.5 High Disk +21

Rear 19x9.5 Low Disk +35

It won't sit exactaly flush but good enough I guess....

Now tyres... I'm was looking at either the Eagle F1 GS D3's or the Falken FK452's. Front would be 225 or 235 and rear would be 265. Does anyone know if the tyre sizes will conflict with what rims size's I'm getting? I don't want to do any modifications, no rubbing either. I don't want my GTT to sit high like a 4WD car... just low enough to make clearance on the tyres so there'll be no rubbing. Any thoughts?

Are those wheels for the wider guards as well? The offset seems pretty high? Sorry, but I'm not all that familiar with skyline guards.

What I usually do for fitment and tyres is, make the wheels flush with the guards and get tyres that are about the same width. So an 8.5" wheel measures 215.9, but closes will be 215mm tyre for example. Not sure how good this will be for performance and that, but yeah...

Are those wheels for the wider guards as well? The offset seems pretty high? Sorry, but I'm not all that familiar with skyline guards.

What I usually do for fitment and tyres is, make the wheels flush with the guards and get tyres that are about the same width. So an 8.5" wheel measures 215.9, but closes will be 215mm tyre for example. Not sure how good this will be for performance and that, but yeah...

Yep, I went with Racing Harts measurments for a R34 GTT... Front 18x8.0 +35 Rear 18x9.0 +38. I then calculated the front... being 19x8.5 +21 offset will give me 8mm more on the inner clearance and 20mm more on the outter. The Rear I chose 19x9.5 +35. That'll give me 3mm less clearance on the inner rear wheels and it'll extend the dish 9mm more. So far, I've found a lot of GTT owners using +35 offset for the rears and had no problems.

now I just want to figure out the right tire sizes without having to sacrifice performance or having to mod guards or having this rub. 215's would most likely make a loss in performance... I think I'll jsut go with 225 in the front. The rear is either 265 or 255. Racing Hart suggested 255 on a 18x9.0 so 265 on a 19x9.5 might work out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...