Jump to content
SAU Community

Recommended Posts

HI all

I have this annoying clicking noise coming from behind my aircon unit when i start the car.

it happens for about 30 seconds then stops.

It is getting pretty annoying does anyone have the same problem? and if so how did you fix it?

its an r33 gts-t.

any help will be great.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/206019-annoying-clicking-noise/
Share on other sites

The clicking noise is from your Air Blend Servo motor (controls hot/cold mix). The gearteeth that control the flap have slipped off. It is really easy to fix, the only problem is removing the whole dash to get to it.

Easiest way is to make sure the heat is maxed all the way up, i.e. slam the red button a million times before u start the car (can be on or off), wont make the sound - leave it like that and wont happen again

hey jmaac

thanks for the advice.

would you know where abouts this blend motor is located on the unit

as due to my ever changin audio needs im somewhat of a pro at dash

removal now :whistling:.

and what to look for in the unit. will the gear be off or could it be that the

teeth have been shaved off.

Thanks

the teeth have basically worn down due to use, they skip over each other as they try to engage causing the click click noise.

i've currently pulled my dash apart to fix it. it's not a small task, at least a 3 hour job to take the dash out.

see attached, note the red arrow on the gear.

the blend door motor is located right in the middle of the dash, above the heater box.

post-9983-1203031896_thumb.jpg

post-9983-1203031962_thumb.jpg

same thing has happened to mine, after a few months im getting a very nast smell eveytime i turn up the heat. i then noticed a wet patch under the dash of the passanger side. If i fix the noise would i stop the damn thing from leaking?

Smell is normal, remove the glovebox and theres a panel which u can remove to clean aircon filter elements

This wet patch is bad, either means your heater coil has rusted out or a hose is broken (b/n firewall and heater)/hose clamp needs tightening (Unless condesations is somehow running back down into your car). U can tie off your heater in the engine bay and loop it around or fix it properly.

Im not sure if u can get replacement gear for these or one from a hobby shop to fit. I used a little glue and was able to build the gear back up, but it didnt last very long. If anyone manages to get a replacement (not 2nd hand) can u please let us know, I may make an plastic injection mould if not avail.

same thing has happened to mine, after a few months im getting a very nast smell eveytime i turn up the heat. i then noticed a wet patch under the dash of the passanger side. If i fix the noise would i stop the damn thing from leaking?

Noise has nothing to do with the leaking. The leaking is probably your heatercore, better to replace it sooner rather than later. The leak will only get worse, and where do you think that water is coming from? Your cooling system - better check and top it up :teehee:

You can bypass the heatercore if you like, just look for the 2 heater hoses going into the firewall on the passenger side, and connect them....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...