Jump to content
SAU Community

Need A Hand With What Exhaust To Get?

4doors13secs

By 4doors13secs,
in Engines & Forced Induction

 Share

Recommended Posts

4doors13secs Contributor

4doors13secs

Posted
Posted (edited)

hey all, i bought my R33 gtst 4 door about 6 months ago and im about to start upgrading it slowly and i was just wondering what exhaust side i should go for? some people have said 3 inch for better perfomance but i dont want it to sound too loud as i like hearing the turbo spool (i no it sounds silly but hear me out lol) and for that some people have said just go 2 and a half as it is stil good for perfomance and not as loud?...

im sort of more lookin for other skyline drivers opinions on it...

thanks..

Edited by 4doors13secs
moobaque Rising Star

moobaque

Posted
Posted

In my opinion its a waste of money upgrading if your only going to go 2.5"

go 3 inch but just make sure there are adequate mufflers in the system. The reason why probably most peoples exhausts are stupidly loud on the street is they only have a resonator/hotdog in the middle instead of an actual muffler (or skipped a central muffler altogether). Also don't make your rear muffler isn't the size of a gas bottle and you shouldn't get any drone. May even consider going twin outlets to keep the exit pipe a smaller size (but at the end of the day its still the same open area) this should help keep the note higher.

I can personally recommend the trust power extreme 2 for being relatively quiet. But i certainly know HKS market a series that claim to be relatively low SPL.

Cheers

Camden

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

I Have a Trust Power Extreme 2 Stainless cat back system and it awesome. I have been pulled over into defect bays and passed 3 times now!!!!!!!! Mind you I was still packing the pants full of goo....

I also have a just jap dump pipe and a high flow cat.... Looks sweet as well... None of the fake titanium tip crap

R338OY Veteran

R338OY

Posted
Posted (edited)

Go 3 inch (that's the recommended size for the motor)

Make sure you get it turbo back.

Don't forget high flow cat convertor. This is pretty essential if you want to remove restrictions.

I can understand the noise factor. I don't like driving around making a racket and getting seen by cops, or even just being uncomfortable in my daily driver. Look around for 'quieter' systems, or get a silencer.

Edited by R338OY
nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

yeah definately go the 3".

I think you can still get exhaust butterfly systems like the Apexi that used to be on the market. I've been looking for one for my car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around with a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
    • joshuaho96
      Squeaking clutch/throw out bearing

      By joshuaho96 · Posted

      Yep, this bit another local owner. I caught it before putting the transmission back into the car, what I noticed was the pressure plate fingers weren't flat and even. It's more obvious with the pull style clutch because the throwout bearing ring was visibly not flat once everything is put together. Nismo should really update their instructions to call out this specific detail. I'm not even sure the clutch as-shipped orients everything properly.
    • jayden_l33
      Squeaking clutch/throw out bearing

      By jayden_l33 · Posted

      It ended up being that orientation of the float hub in relation to the clutch disk, when I installed it, I heard a loud click and being stupid, I decided to not take it a part and check it. The hub didn't properly align with the clutch disk and was causing the issue. Definitely an odd one! Dahtone Racing was able to fix me right up, stand up blokes!      
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Right, but I'm saying on the stock ECU measured airmass from the MAF is no higher than stock. So it's accounting for the higher flow rate iso-manifold pressure. You just have to keep turning down the boost until you're within the stock tune's load scale. If you run off the end there's no telling what will happen. This does mean there's zero benefit to the turbos you're running vs stock, if anything it's just a straight downgrade because the transient response is worse, you don't even get the ECU's boost solenoid helping to pull the wastegate closed during initial spool, and peak power is only whatever the factory map can give you before you hit the R&R corner. On a -9 I would bet that you would have to change out the wastegate spring once you have a real ECU and you're tuning it for real. I'm not saying this is a remotely ideal state of affairs, it's just a way to keep it driveable until you can get a proper tune done.
×
×
  • Create New...