Jump to content
SAU Community

Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

What's the best time to get there to enter?

Me and a couple of mates are going to have a run tomorrow night

gates open at 5 for competitors, sometimes 4.50pm thel open, then u got through scrutineering and then u will probly wait around for half an hour or so coz racing starts at 6pm

yep - rev limit clutch dump works well :cool:

nah - something around 4000rpm works from what ive read, then bleed the clutch out or pop it out if you got a hd clutch

otherwise just work around that value - try 4000rpm one time, then 4500 rpm then 3500 rpm, then just feel around them till you find something that works for you

lately ive seen a few gtrs down at the strip runnin like 14s alot off ppl are revvin to like 3000 3500 droppin the clutch and its just bogging off the line, depends really if u gotta heavy duty clutch or not, if not i wouldnt try launching too hard, if u do i think ya should git it 4000rpm+ and practise gettin off the line without bogging it

4000rpm should be alright, i notice some people rev it o 4000rpm and straight out drop the clutch and it bogs, if u go a bit slower on the clutch to keep the revs up and give it plenty of throttle it should launch ok, i have got a 2.0sec 60ft last week in my gtst

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...