Jump to content
SAU Community

Recommended Posts

Does anyone know if you can get the factory seat cloth for GTR R32

I want to re trim my drivers seat in factory trim, and would like it if i could supply the fabric to the trimmer

Anyone know where u can get it from, or what its called, colour code etc??

Thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/207874-r32-gtr-seat-cloth/
Share on other sites

I actually tried this awhile back, and it seems that gtr seat material isn't really consistent in colour due to rapid fading etc.

There actually isn't a colour that i could find that is the same. were many similar but not the same. So i had to retrim in another material/colour.

Also its quite expensive to retrim the seat itself about $300 labour alone excluding materials as the gtr seats are quite complex in design. And also because the seats material is all one piece, you will also need to replace the suede aswell, and if you go genuine suede its quite costly. Costed me about $700-$800 a seat for leather/suede seat retrim.

A GB on this would be good, but the thing is, it would have to be either:

Fabric ready to go

or

Fitted to the seat

And if its option 2 then has to be the one city.....actually ill try some places and see about doing one for sydney

^^ Is the seat really worn or just a few tears?

If tears then I get a few iron patches and glue it on. Thats what I did LOL!

If ya having trouble getting the fabric just buy a BRIDE Seat. LOL!

closest seat material to original macro suede type is probably 'alcantara' as used by lambo, audi, porsche, amg etc and available from Gineico in Sydney from memory about $110/m on a 1.4m wide roll. classic british and german in sydney have a similar product but slightly coarser and more expensive. there are similar alternatives but i can't vouch for them. alcantara is bullet proof hence why they use it on ferrys etc. as it is very wear and uv resistant. unfortunately due to fading and batch changes etc its unlikely you can ever match the original perfectly.

closest seat material to original macro suede type is probably 'alcantara' as used by lambo, audi, porsche, amg etc and available from Gineico in Sydney from memory about $110/m on a 1.4m wide roll. classic british and german in sydney have a similar product but slightly coarser and more expensive. there are similar alternatives but i can't vouch for them. alcantara is bullet proof hence why they use it on ferrys etc. as it is very wear and uv resistant. unfortunately due to fading and batch changes etc its unlikely you can ever match the original perfectly.

cool sounds like good info tho

i will see what i can do

i def want to re trim the seat but in factory gear :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...