Jump to content
SAU Community

Recommended Posts

Sorry if it's a repeat topic, I did some searching and didn't come up with anything (forum search software blows).

Now, I'm about to get a FMIC on my R33 S2 and I wanted to know, where is it ok to put my front number plate?

I've seen a couple of cars with it off to the left hand side which is good for me because I'm wanting to do a simple air-intake where the side mount used to be. But what are the legalities involved with relocating the number plate?

Eventually I'll get a slimline plate for the front to make things easier (plus I prefer it to be the the center -- looks more balanced), but until then where can it go?

Link to comment
https://www.sau.com.au/forums/topic/209827-front-number-plate-placement/
Share on other sites

looking at the car headon i've got mine on the bottom right haven't had problems with p olice or n ething they pulled me over b4 but never said ne hting about the number plate bein there =)

seen a few people with it on the left

Get some custom plates and get a slim line plate for the front :action-smiley-069:

Yeah, I think I might have to do that sooner than I thought. Maybe I'll just mount the number plate a little higher until I have more money to blow on plates. :)

20070825-3473.jpg

The hard thing is, space is pretty limiting. The fog lights may be a bit too much in the way to put it off to the left.

Get something like a couple of L brackets & join it to the bumper in the gap underneath the lights.

Yeah, I think I might have to do that sooner than I thought. Maybe I'll just mount the number plate a little higher until I have more money to blow on plates. :action-smiley-069:

Yea, thats what I've done. I just made a bracket that lifted the whole plate up by about 60 to 70mm.

Mine is mounted on the drivers side on my BNR32 Righthand side. Cops have pulled me over and said nothing. And unfortunately the multinovas still get ya. Comes up clear as day in the infringement photos. :banana: and i'm sure thats all the police care about.

Edited by Public Enemy

I have a Cusco number plate offset kit that uses the original holes and moves it off to the passenger side. I never used it. Stainless steel bracket, still in the packet. (That rhymes!)

Let me know if you are interested. By the way, all Alfa Romeos have it on passenger side from factory. The only legal requirement that I am aware of is that it has to be mounted so that it is parallel with the axle - so you cannot have too much of an angle.

Cheers. :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...