Jump to content
SAU Community

Recommended Posts

The screw aloows you to adjust hte spring tension. When you are running more bosot pressure you might find it starts to leak in higher rev's so you want to tighten the srping up, however if you are not running as much boost you want to loosen it off to ensure the BOV will be able to open. However they more adjustable nowdays for rice factor to get different sounds.

BOV"s are illegal for the reason being that they vent blow-by into the atmosphere... yes they can be noisey, yes they cause the car to run richer but its stated that they blow un-filtered air/oil into the atmosphere... stupid really, cos last time i checked the exhaust vented to atmo aswell?? But thats all good its only carbon monoxides and what have you, alot worse than the 'ocassional' mist of oil comin from a BOV.

P.s. Don't forget BOV's if they aren't a good design will cause crappy throttle response, and having a atmo BOV means you must re-spool that released amount of air. They have their pluses and minuses.

As YBSLO4 mentioned BOVs are illegal if they vent to atmo, because cranck case gasses must exit the car via the exhaust, Road Traffic Act 1962 (from memory) in SA. These traffic laws are now pretty much consistant australia wide. So they MUST plumb back to be legal - like the stock one.

As for adjusting BOV, tighter will mean it takes more (boost) pressure for the valve to lift. Yes it will make less noise, but the fluttering noise you hear is air reversing through the compressor, slowing the turbo down (increasing lag) and putting strain on the turbine - this isnt too good for obvious reasons.

I adjusted mine by winding it back until the fluttering sound was almost gone. Almost, because if you wind it back too far, you may have the car stall at idle as it doesnt seal properly. Something to have a play with until you are happy.

The only noise testing I know of that a car needs to be roadworthy has to do with the exhaust, this is done with the car at revs, and the EXHAUST is not to exceed 89dBs. This is conducted with the car at specific revs, not changing gear - so I am not sure how any copper gets away with defecting cars for excessive intake noise (how could it exceed 89dB?) or noisey BOV which wouldnt be measured if a car was being tested for compliance with noise regulations - only for atmo BOV or pod that doesnt comply with ADRs.

I have heard of people claiming to be defected for this, and I would love to know exactly what regutation/act it is that they would be in breach of?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Order for the 2025 model R35 GT-R were accepted from 3rd March and 26th August the last order rolled off the production line at the Tochigi plant. Concerning the R35 GT-R replacement, current Nissan CEO Ivan Espinosa said "Nothing has been decided about the GT-R at this time, but we are well aware that everyone is waiting. The GT-R will evolve and reappear in the future. Please be patient until that day comes." Nissan has a lot of issues with management and finances so take Espinosa's words with a big grain of salt. From what discussions I've had and read about here in Japan, not a lot of people are confident about Nissan's future, let alone the next GT-R. 
    • Thanks. We getting some parts along too so he will be solving the speed issue like next week so i will let you know what he came up with.   
    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
×
×
  • Create New...