Jump to content
SAU Community

Enkei Rpf1 17x9.5 - Drifteks- Meshies - Disco Potato


Recommended Posts

For Sale:

* 4x Enkie RPF1 17x9.5 +18 5 Stud - months old no scratches or anything look brand new. pretty rare never seen them with good offset in australia before. They fit with no spacers on the front with coilovers. Will fit under standard guards with some guard rolling and camber.

Pics on car are with 0 camber rear and 2.5 neg on the front with 30mm guards

These are very light, weigh in at just 7kg's each

Comes with FED 595's on the front only used for a week. And pretty used maxxis tyres on the back

$1800

* 4x Drift Teks 17x9.5 +18 5 Stud 2 of them have been powder coated white and 2 are still bronze. They have a few scratches.

$900

* Sard 550cc Injectors suit SR Been cleaned and new o rings at the start of the year

$350

Work wheels 18x9.5's +2 just a pair freshly painted black

$400

Blitz Nurspec Cat back exhaust

$250

Garrett gt28rs Disco Potato, used for a few months, no shaft play. 0.86 rear housing. with exhaust manifold and split dump pipe. Braided oil feed line, and stock water lines. Has aftermarket oil drain flange from GCG with the line too

$1000

BBS Meshies - 17x8 +35 5 stud offset pair only have driftable tyres on them

$130

Pics:

IMG_0839small.jpg

IMG_0838small.jpg

IMG_0836small.jpg

IMG_0837small.jpg

enkei_rpf1_silver.jpg

Image000-1.jpg

06042008.jpg

0604200w.jpg

Image007-2.jpg

Image006-1.jpg

05042008a.jpg

07042008.jpg

07042008-1.jpg

12042008-1.jpg

12042008.jpg

10042008-1.jpg

10042008.jpg

Location: South Brisbane

Contact: 0401151011 or pm

Edited by Waldo
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Thanks, I checked from the back of the cluster and no reading there. I undid the connector and plugged in the wires directly to start from where I'm getting a reading: https://imgur.com/a/W8JI6Yr Weirdly enough when I tried to get a reading from the crimps that connect to the fuel pump assembly, I got nothing. Not sure what's my next step as I have admittedly limited knowledge with electricity. 
    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
×
×
  • Create New...