Jump to content
SAU Community

Recommended Posts

Hey people,

I went out to Qld raceway on the weekend and I noticed an occasional cut of power. I've had misfires before but this was not like a misfire, it was more like a complete stall for about half a second.

It seemed to happen as I'd come around to the end of the last corner (long right hander). Also, I started the day with a full tank and didn't experience the cut in power until towards the end of the day when I had half tank, so this was making me think fuel surge.

But the other thing that changed between the start and the end of the day was my driving style. At the start I was putting around the corner a bit slower in 3rd gear, but at the end of the day (when I experienced the cut) I was sliding the corner full throttle at the top of 2nd gear (not bouncing off the limiter but was high in the revs as you'd imagine sliding a corner).

So the other thing I'm thinking was I may have hit a boost cut (or fuel cut)? I don't have a boost controller, and I'm pretty sure I have a standard turbo and actuator, but for some reason I'm getting 0.9Bar (over 13psi) at the inlet manifold. Should I expect some sort of boost cut at this boost level?

This is on a standard RB20, standard turbo, standard ECU, walbro fuel pump, R34SMIC. I do have a completely straight through turbo back, so I would expect a few PSI more than standard, but I think 0.9bar is a bit higher than normal.

If it is likely to be fuel surge then I have no problems getting a surge tank, I just don't want to fork out the money if I need to be spending it on getting a retune or something.

Thanks, Luke

Edited by daisu
Link to comment
https://www.sau.com.au/forums/topic/212869-fuel-surge-or-fuelboost-cut/
Share on other sites

Good Q!

Fuel surge, or a ECU initiated cut...

If your car never cut before (too much AFM voltage output) while loaded on the street (3rd gear, up hills = boost = AFM output) Then i doubt it would see that same load, wheel spinning in 2nd out a apex.

I reckon it be fuel surge.

Cant you run the car to the same fuel level and generate some lateral G forces to test?

Good Q!

Fuel surge, or a ECU initiated cut...

If your car never cut before (too much AFM voltage output) while loaded on the street (3rd gear, up hills = boost = AFM output) Then i doubt it would see that same load, wheel spinning in 2nd out a apex.

I reckon it be fuel surge.

Cant you run the car to the same fuel level and generate some lateral G forces to test?

Yeah it hasn't cut out before, but my reasoning is that say going up a hill in 3rd at full load, the RPM would probably only be getting up to about 5krpm, whereas on the track at full load in 2nd I was probably close to the limiter, so there would have been more air flowing into the engine.

I could hook a multimeter up to the AFM output and get a mate to monitor it next time I'm on track. Or are there commonly available methods of monitoring fuel pressure remotely? (like an electronic oil pressure gauge, but obviously I'd need something with a different pressure range).

Yeah it hasn't cut out before, but my reasoning is that say going up a hill in 3rd at full load, the RPM would probably only be getting up to about 5krpm, whereas on the track at full load in 2nd I was probably close to the limiter, so there would have been more air flowing into the engine.

Yah, g.point, I assumed you woulda caned it up a hill once or thrice, making your setup feel max load before.

I could hook a multimeter up to the AFM output and get a mate to monitor it next time I'm on track. Or are there commonly available methods of monitoring fuel pressure remotely? (like an electronic oil pressure gauge, but obviously I'd need something with a different pressure range).

Ummm, I think you getting confused lol.

AFM measures air into into the motor and spits out a 0-5v signal (which a fast acting MM could read)

Im not OG with RB20 cuts so cant help you there.

Fuel pressure will need to be measured with a mech gauge, T'd into your rail feed, b4 FPR obviously. Run the line dodgy styles out the grill, through the window as a temp setup. Your shotgun will have to keep a keen eye on it.

Of course a lecky gauge with a f.pressure sender, recorded by a logging instrument (Innovative, Datalogit etc) would be best.

Your correct; many manufactures use the same sender for both fuel and pressure (like Defi)

Start with the easy stuff first,

1) Find out when RB20's with your mods ECU cut

2) Fill car up, find a quiet, sticky corner, or private road. Let car run down to the fuel level it had before... and try again. Should pretty apparent I would think.

GL :ermm:

Edited by GeeTR
Yah, g.point, I assumed you woulda caned it up a hill once or thrice, making your setup feel max load before.

Ummm, I think you getting confused lol.

AFM measures air into into the motor and spits out a 0-5v signal (which a fast acting MM could read)

Im not OG with RB20 cuts so cant help you there.

Fuel pressure will need to be measured with a mech gauge, T'd into your rail feed, b4 FPR obviously. Run the line dodgy styles out the grill, through the window as a temp setup. Your shotgun will have to keep a keen eye on it.

Of course a lecky gauge with a f.pressure sender, recorded by a logging instrument (Innovative, Datalogit etc) would be best.

Your correct; many manufactures use the same sender for both fuel and pressure (like Defi)

Start with the easy stuff first,

1) Find out when RB20's with your mods ECU cut

2) Fill car up, find a quiet, sticky corner, or private road. Let car run down to the fuel level it had before... and try again. Should pretty apparent I would think.

GL :P

Lol Not getting confused, probably the way I worded it.

I was saying I could either monitor the AFM to see if I'm reaching it's limits, Or I could monitor the fuel rail pressure to see if its fuel surge. Basically just what you explained.

I wasn't saying that measuring the AFM would tell me if I was getting fuel surge, I was more getting at the point that unless I used a tee piece and mounted a gauge outside the bonnet I'd need some sort of electronic gauge and sender suitable for this pressure range.

I suppose It wouldn't be that hard to tee the fuel line and sit a gauge at the bottom of the windscreen on the passenger side(outside obviously).

But now I'm think measuring the AFM voltage will be easier, safer and more accurate.

Reason is, if I measure the fuel pressure and hit an ECU cut (caused by AFM limits) the engine will stop producing power momentarily, which will also drop the boost pressure. Since the FPR is also controlled by the boost pressure I would also see a drop in fuel pressure, which could be misleading.

If I measure AFM voltage and it is reaching it's limits, I would see it increasing to a certain point at which the ECU would initiate a cut (close to 5V). Or if it was a fuel surge I'd see the AFM voltage holding steady then dropping slightly when the engine cuts out (hopefully it doesn't happen at close to 5V otherwise it would be a bit inconclusive).

Next time on track is this Friday night, so hopefully I'll be able to find the problem then.

Other thing I could do is repeat the driving style with a full tank (as opposed to a half tank). There should be no fuel surge with the full tank. So if it does cut out then I could safely assuming I've reached the AFM limits, and it's time to upgrade turbo/injectors/AFM and retune.

If it doesn't cut out then I would assume it's the fuel surge and I'll get the surge tank in there.

Also, going full throttle up a hill would be full load on the engine, but the engine would not be using the same amount of air unless the RPM was the same. Kind of hard to replicate something like 7krpm full throttle on the streets as 1st gear would just be wheel spin and hit limiter too fast to measure anything, and 2nd gear would be going too fast for public roads.

Edited by daisu

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...