Jump to content
SAU Community

Recommended Posts

Item:R33 GTR steering wheel

Age:96

Condition:excellent

Price:$295.00

To Fit:R33 GTR/GTS

Location:Sydney

Contact:Jerry, pm or email [email protected]

Comments: The wheel is in excellent condition and includes the airbag, will post anywhere at buyers expense.

post-5240-1207523587_thumb.jpg

post-5240-1207523601_thumb.jpg

Edited by wrxhoon
Link to comment
https://www.sau.com.au/forums/topic/213767-r33-steering-wheel/
Share on other sites

Hey, just curious. is there any wear on the steering wheel?

also will this fit into a series 1.5? :blink:

thanks

No wear, if you are keen and not in Sydney i can send you high resolution pics. Will fit series 1.5 GTS.

No wear, if you are keen and not in Sydney i can send you high resolution pics. Will fit series 1.5 GTS.

I am keen, my steering wheel is worn out and makes rattling noises, i think one of the previous owners used to wear rings so alot of the leather? has been worn off.

My email is [email protected] thanks.

I'm in melb btw.

I am keen, my steering wheel is worn out and makes rattling noises, i think one of the previous owners used to wear rings so alot of the leather? has been worn off.

My email is [email protected] thanks.

I'm in melb btw.

Email sent with close ups.

Is this still for sale? Im very keen as I need an airbag steering wheel to pass rego! $295 is no prob. From Newcastle so I could arrange pick up if you were willing to meet halfway, otherwise, post is fine.

  • 3 weeks later...
Is this still for sale? Im very keen as I need an airbag steering wheel to pass rego! $295 is no prob. From Newcastle so I could arrange pick up if you were willing to meet halfway, otherwise, post is fine.

Still for sale ..

  • 3 weeks later...
  • 2 weeks later...
This is still for sale, plenty of interest but all tyre kickers.

I am not a tyre kicker,

I haven't been on the net for a month but I was all set to purchase this item, but I still haven't gotten an answer from my thread about if this will fit my car.

I'm still looking into it tho.

Thanks.

  • 1 month later...
  • 5 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...