Jump to content
SAU Community

Recommended Posts

Make:Ford

Model:2006 BF XR6T

Milage:18,000kms

Transmission:6sp Manual

Colour:Bionic Blue

Location:Melbourne, Eastern Suburbs

Complied?yes

RWC supplied?yes

Currently registered?yes

Price:$33,500

Contact:0401-004-999

Car was bought new and has Tinted windows, lowered with King Springs, Typhoon Air Snorkel, K&N Filter and Premium Sound, XR scuff plates and Xr Mats.

Will take trades of all descriptions if car suits but preferably GTR.

post-8487-1207791501_thumb.jpg

post-8487-1207791517_thumb.jpg

post-8487-1207791534_thumb.jpg

post-8487-1207791560.jpg

Edited by glaze
Link to comment
https://www.sau.com.au/forums/topic/214268-fs-2006-bf-xr6t-6sp-manual-18000kms/
Share on other sites

  • 2 weeks later...
  • 2 months later...

Hey Sloutch, yeh they would save about $15-$17k from brand new!! It doesnt matter so much now as I think you have sold your car, so not so desperate anymore:(

Congrats on the sale!!

Price Drop $28,500 or interested in trades and cash adjustment my way!!

Car has had full exterior detail with all stickers removed!!

Throw those trades at me Guys-GTR,GTST,GTO etc etc not too fussed!!

Edited by glaze
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...