Jump to content
SAU Community

Problem With Stereo

Killa33 Skyline

By Killa33 Skyline,
in Car Audio & Electrical

 Share

Recommended Posts

Killa33 Skyline Apprentice

Killa33 Skyline

Posted
Posted

Hey all :wavey:

Got a problem with my stereo, everytime i turn it up (to decent volume) the speakers cut out. I have a JVC headunit, splits in front, 6X9's in rear which run off 1 amp, a inline fuse which has volt reader and spliter from single to twin and Pioneer sub that runs off another amp. I've tried replacing the remote wire for the speakers amp, didn't work. I've tried swapping with a different amp, didn't work. :down: It's only the speakers that cut out, can still here the sub thumping away. Was considering redoing the wiring for the amp next, does anyone have any other suggestions to my problem.

Link to comment
https://www.sau.com.au/forums/topic/214304-problem-with-stereo/
Share on other sites
Killa33 Skyline Apprentice

Killa33 Skyline

Posted
  • Author
Posted
hey man have you tried just running the 6 by 9's by itself and see if it cuts out.. or just the splits by it self.

Yeh at the moment i only have the 6X9's running through the amp, still got the same problem.

Most likely your fuse and/or cable isn't large enough for the amp to run at full capacity(which is why it works on lower volume).

Check the connection is secure on the power line splitter also.

Cheers mate will check it out when i get back home.

  • 3 weeks later...
turbo_brian Community Regular

turbo_brian

Posted
Posted

+1 for thermal overload.

Also, what grounding have you got on the effected Amp??

Remember, dont ground 2 amps at the same point, use 2 different grounding points, make sure they both have strong contact points, and the cable is sufficient.

B.

Killa33 Skyline Apprentice

Killa33 Skyline

Posted
  • Author
Posted
is your 4 channel amp overheating (thermal overload)? touch it they can get ridiculously hot after a good thrashing

Not sure, but even first thing it still cuts out.

+1 for thermal overload.

Also, what grounding have you got on the effected Amp??

Remember, dont ground 2 amps at the same point, use 2 different grounding points, make sure they both have strong contact points, and the cable is sufficient.

B.

Will have a look at this as, cable should be sufficient for ground. but i think they may be earthed out to the same point of contact.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
×
×
  • Create New...