Jump to content
SAU Community

Recommended Posts

Hey Guys,

I picked up my R34 yesterday. I'm so happy, so I had to post up some pics :blush: They are a bit covered in rain, but this is the only gap I got :D

post-29218-1208417926_thumb.jpgpost-29218-1208418124_thumb.jpg

post-602-1134975445.jpg

... and I had to take some pics of the pair :blush:

post-29218-1208418429_thumb.jpgpost-29218-1208418522_thumb.jpg

edit: and some interior pics just for Karl :w00t: Sorry about the bad quality of these. Just ran out and grabbed them :banana:

post-29218-1208420776_thumb.jpgpost-29218-1208420832_thumb.jpg

post-29218-1208418269_thumb.jpg

Edited by R33-GTS
Link to comment
https://www.sau.com.au/forums/topic/215293-my-new-r34/
Share on other sites

Thanks :banana: Yea, I have pretty big plans actually.

I'm building it to mainly compete in the autotest series. For this braking and suspension are key. Also, bucket loads of power will not do any favours, so to start I'll be going for between 200 and 210 rwkw. Here is the list to get there...

Engine

- RB20 wastegate actuator (increases boost to 10psi)

- FMIC

- CAI

- High flow filter

- Power FC (if I can find one :D)

- 3" turbo back exhaust

- Iridium sparkies

- Tomei Fuel pump

- Surge tank

Suspension wise

- Tein SS with EDFC

- Pretty much a whole heap of whiteline stuff to make everything adjustable

Braking

- G4 Racing brakes all round with nice big rotors for big stopping power

Body Kit

- C-West front, sides and rear

- z-tune front fenders

- Cross Factory rear fenders

- 18x10.5 Work Meister rims with some 285 or 295 rubber (lots of grip )

- East Bear vented bonnet

- R34 GTR spoiler

ICE

- Pretty much pioneer everything from head unit to two shallow 12" subs in a custom moulded boot

Link to comment
https://www.sau.com.au/forums/topic/215293-my-new-r34/#findComment-3802959
Share on other sites

Thankyou to which ever mod reopened the thread :banana:

I gotta say dude you got a damn fine ride there, looks real clean.

Looks like you've got a good plan on where your going :)

If you want to change from center triple gauges to GTR mfd screen, I might be able to help with the wiring :D

Link to comment
https://www.sau.com.au/forums/topic/215293-my-new-r34/#findComment-3803392
Share on other sites

Thanks for the comments guys :)

Yea, there is definately a big difference between the R33 NA and the R34. Turbo pulls a lot harder, thats for sure :banana:

Yes... it is definately a manual this time. After driving an auto for a while, I was definately missing the manual. Wouldn't go auto ever again lol

Link to comment
https://www.sau.com.au/forums/topic/215293-my-new-r34/#findComment-3803757
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...