Jump to content
SAU Community

Sup Homies

Dearlove

By Dearlove,
in Introduce yourself

 Share

Recommended Posts

Dearlove Collaborator

Dearlove

Posted
Posted

hi all

name is trent or dearlove, im easy

just bought myself an r32 gtr, 93 model

well i'm the fool

here's the story

look at buying a gtr- do a bit of research on what I'm buying

buy gtr- do a lot more research and find my engine is prob going to blow and cost me 10-15k to rebuild... and then there is still a chance it will blow again.... ha

Link to comment
https://www.sau.com.au/forums/topic/215975-sup-homies/
Share on other sites
Dearlove Collaborator

Dearlove

Posted
  • Author
Posted

its the SAU whore

im sure it had a bloody hard life,i mean even for a gtr

i think its godthrilla's old one

Mods-

Pod filters

Large 100mm intercooler

A/M front pipe

Cat pipe replacement

Tein height/spring/dampener adjustable coilovers

Nismo control arms

Nismo front and rear strut braces

Modded ECU (more power, rev/speed cut removed)

Apexi AVCD 5 dial boost controller

HKS turbo timer

Whiteline pineapple kit

Heavy Duty 6 Puck clutch

3in Turbo back

Exterior-

Full N1 bodykit (front bar pods, bonnet lip, skirts, rear boot lip)

N1 headlights

Tinted windows

17x9 +22 Rays GT AV's ( with brand new tyres)

Past owner ran a 12.2 Q/M @111mph

Interior-

Genuine NISMO GTR floor mats

Fusion 5" splits in factory location, Alpine 6" 2 ways rear

Blitz boost gauge

Dynamco alarm and CDL

post-37126-1208904473_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/215975-sup-homies/#findComment-3816026
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...