Jump to content
SAU Community

Frount Mount Intercooler Question...

kidafa

By kidafa,
in Four Door Family & Wagoneers

 Share

Recommended Posts

kidafa Veteran

kidafa

Posted
Posted

Hi all,

Tonight adam (chefstagea) and I have got about 90% of his frount mount intercooler installed into his S2 stagea... Just got the last piece of piping to go and we have a slight question about it:

On the stock piping their was a small nipple with a black line going to it... Ive seen some intercooler kits which have these nipples on the new piping. Adams kit doesnt have the nipple on the piping. What does this nipple do? Im thinking ill go get one put into the piping while hes at work tomorrow. Where can I get the nipple installed? (exhaust shop maybe?)

the nipple I'm talking about is the one you can see here on the middle piece of piping:

med_gallery_35770_2483_42222.jpg

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/217176-frount-mount-intercooler-question/
Share on other sites
darrinspencer Grand Master

darrinspencer

Posted
Posted

On a series 2, you will need 2 nipples. One for boost and the other goes to the power steer pump.

I used a brass screw in nipple found at most auto parts shop. Drill a hole, and screw it in. The alloy pipes are fairly thin so I used some liquid metal approx $8 tube to fillet around the nipple and the pipe to make it stronger.

kidafa Veteran

kidafa

Posted
  • Author
Posted

How to install nipple into a Intercooler pipe:

What you will need:

Brass threaded nipple fitting, with a 1/8 BSP tread on end (Sprint Auto $4.95)

1/8 BSP tap kit (from motortrader $37). This kit is needed as thread on nipple is a gas thread, thus it tapers

White plumbing tape

3mm Drill bit

8mm Drill bit

Heat silicon/sealent

Procedure:

Mark the spot that you would like the nipple with a scratch

Take 2mm drill bit a drill a pilot hole for the 8mm

Drill out hole with 8mm drill bit and more it around a bit to make room for tap

Tap 1/8 BSP thread into pipe

Place 2/3 layers of plumbing tape around the threads on the nipple

Screw nipple into piping and fastern firm but not over tight as intercooler piping is a bit soft could easily pull threads out

Place some heatsilicon/goop around bottom edges of nut on nipple just to ensure the seal is 110%

Happy days!

No finish Installing your frount mount intercooler, with one less thing to worry about :D

darrinspencer Grand Master

darrinspencer

Posted
Posted

One more step, make sure you clean the inside of the pipe very well after to make such there is no metal bites from drilling. don't want them going thru the engine.

No need to buy expensive taps, as the thread is tapered it will cut it own thread, esp in the alloy pipe.

  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
    • TurboTapin
      Most women will agree that parking is the most taxing part of driving

      By TurboTapin · Posted

      What a time to be alive!!
×
×
  • Create New...