Jump to content
SAU Community

Recommended Posts

Hey Guys,

Time has come to sell the car, moving on to much nicer things hopefully.

Details are as follows -

1998 Series 2 R33 - Silver - Looking for $16000

Engine

Forged Rebuild (have reciepts)

Blitz FMIC & Pod

3" Nismo cat back Exhaust (very quiet), 3" split dump/front

Blitz Dual SBC Boost controller (runs about 10psi)

Apexi SAFC II

Turbosmart BOV

Inside

Greddy Turbo Timer

Dildo Gear Knob

Blitz Boost Guage

Outside

Factory Aero (skirts & rear aprons)

Volk GT-P 17x9 front and rear. Good offset...

Suspension

Cusco Camber Arms

Cusco Traction Rods

G4 Coilovers (8kg front, 6kg rear)

Basically a nice all round street car, but would be very capable at circuit work or drifting.

You wont find many cleaner examples, Most would have seen it out at QR, Archy, Stadium drift events.

Not sure if the plates will go with the car, can be talked through with potential buyer.

Neil

Pictures -

Nissan%20Skyline%20R33%20-%201.jpg

Nissan%20Skyline%20R33%20-%203.jpg

Interior%201.jpg

Nissan%20Skyline%20R33%20-%204.jpg

Interior%202.jpg

Nissan%20Skyline%20R33%20-%202.jpg

Link to comment
https://www.sau.com.au/forums/topic/217511-nissan-skyline-r33-series-2/
Share on other sites

what sort of power are you getting?

To be totally honest I have never dyno'd the car, so I don't know.

there are people running stock motors with similar mods making near on 200rwkw so I'd say that is possible with a proper tune. However the car is a turbo, injectors and ecu away from big big power for someone that wishes to.

Neil

Edited by mr_squiggle_1

interstate transport youd be looking at around $400 which for this car i can say well worth it. damn so nice clean and simple

wow, looks tidy, is anyone knows how much would it cost to transport a car like this to sydney?

how much has the chassis done?

wow, looks tidy, is anyone knows how much would it cost to transport a car like this to sydney?

how much has the chassis done?

Chassis has done 133XXX km's. I dont think car has had the clock turned back upon import, as the condition of it leads it to have that many k's at the most.

Im willing to send interstate if the buyer organises the transport. Not looking for swaps of any kind as I have a car lined up already.

Neil

Chassis has done 133XXX km's. I dont think car has had the clock turned back upon import, as the condition of it leads it to have that many k's at the most.

Im willing to send interstate if the buyer organises the transport. Not looking for swaps of any kind as I have a car lined up already.

Neil

forgot to ask how many kms have u put down since engine rebuilt? cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...