Jump to content
SAU Community

19inch Buddyclub Rims (new)

Sr PWR
 Share

Recommended Posts

Sr PWR Rising Star

Sr PWR

Posted
Posted

Item: buddyclub p1 2s HYPERGOLD

Age: 2 months

Condition: brand new

Price: swap/ $2500 FIRM

To Fit: (What car) 5 stud

Location: qld

Contact: pm

Comments: these rims are basicly brand new, im looking at trading for another set of 18inch deep dish rims,GOOD s13 coilovers or bride seats/32 gtr or straight out cash :) etc. the widths and offsets are 19x8.5 with a 38 on the front and a 19x9.5 and 38. these rims have been fitted to a 180sx (wit 5 stud) r33, r34. The rims are in there original boxes ready to go!!

they are also fitted with 235/35/19inch tyres all round which are also brand new, (2000kms old)

Attached thumbnail(s) img-resized.png Reduced 74%post-36892-1208607535_thumb.jpg 566 x 447 (156.63K)

post-36892-1209949688_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/217766-19inch-buddyclub-rims-new/
Share on other sites
n15m0 Grand Master

n15m0

Posted
Posted

would you sell the wheels without tyres? The tyre profiles are not correct for my car..

Also have a set of black SSR professors if you want to swap

18x8.5 +35

18x9.5 +35

With Falken tyres between 10-40% thread left.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...