Jump to content
SAU Community

Recommended Posts

Guest Robo's

This is the first car i have had with severe oversteer. I want to reduce it!!

Its got Tein NR suspension, rides very firm, i feel this maybe the cause. Also 17*9 at the rears with 255/40/17 which mean it should hang on, but it doesnt, any good throttle will send the rear out, i might try reducing the back tyre pressures to reduce it.

Anyone elses opinion.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/
Share on other sites

you only reduce ur tyre pressure if you, say driving a 4WD on a sandy beach so your tyre didn't sink.

Or, you go to drag race and need a little tyre wall flex so you get more grip on hard (straight) launch, not just bumping around the track.

For anything else, pump up your tyres with enough pressure in it, coz they're good for corner handling and less rolling resistance will save fuel.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-462741
Share on other sites

youll need to do some more research. My konis are adjustable, but you have to remove the shock, fully compress it, and rotate the rod to adjust the damping, there are no external adjusters so they dont LOOK adjustable.

Maybe have a look at your rear camber, and make sure there is no rear toe out as previously suggested. Might have excessive rear camber.

I would even take it to a suspension specialist, get them to look at all the suspension mods and alignment, then drive the car, and work from there.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-463585
Share on other sites

I've got the whiteline kit with adjustable sway bars, front on hard and the rear in the middle. still find that on fast tight corners (eg turning right at lights at around 60, no traffic around!) it has a tendency to understeer just a little, but then to flip into oversteer without much/any warning. can be rather scary and hard to correct, to the point that i have a little less confidence in the car's handling than i feel i should. the rear end is far less "twitchy" than a lot of rwd cars i have driven, but the way it can just snap out on you with no warning worries me.

Question, i guess, is should i try full soft at the rear sway? the shocks are bilstein all round but not adjustable

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-478845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...