Jump to content
SAU Community

Turbotech Manual Boost Control Problems

pitoui

By pitoui,
in Engines & Forced Induction

 Share

Recommended Posts

black_gtst Proficient

black_gtst

Posted
Posted

def install a guage before you start stuffin round setting it. sure you have it the right way round n in the line 2 the wastegate? ball isnt jammed in the bottom or something silly like that?

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

i cant believe you would screw it in all the way to see what would happen.

damn man! that would seriously do some bad ass damage to your engine! those turbotechs are savage when bringing theboost on and they work.

it was probly running 25psi or something silly like that.

take to get it dyno'd and check the afr's as well because you could stuff your engine otherwise.

also buy some bcpr7es spark plugs and gap them to .8 before you go there.

dmr Mentor

dmr

Posted
Posted (edited)
No worries, thanks for the help, I'll just keep it in for now and not boost it. Definately will buy a gauge tomorrow.

i can't beleive you installed and tested the boost controller without a boost guage! you could seriously do some damage to your engine.

your car is likely to splutter due to ecu fuel cut because of free boost or very high boost. remove the controller and ensure you install a boost guage before you start fine tuning the boost controller, otherwise you may damage your engine.

also, i wouldn't advise running more than 12PSI without a dyno tune because your car may lean out.

cheers,

dave.

Edited by dmr
pitoui Contributor

pitoui

Posted
  • Author
Posted

Yeah I definately stuffed up, I know that the more you screw it in the more boost you will get.

I took it out now, it's running stock boost.

I've run into another problem though, as soon as the car hits 5000 revs and over it sorta dies in the ass. I think it may be leaking boost or something. It's been doing this since I installed my front mount. Has it got anything to do with my HKS SSQ BOV?

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...