Jump to content
SAU Community

Spark Plug Change Issues

Logikal

By Logikal,
in General Maintenance

 Share

Recommended Posts

Logikal Collaborator

Logikal

Posted
Posted

Hi all,

Have a bit of a drama with changing my spark plugs and I have a feeling something extremely bad has happend.

Story goes, last Saturday I bought some new spark plugs (NGK BKR6ES) and tried swapping them around with my old plugs (NGK Iridiums that were put in by Gavin Wood Autotech on the Gold Coast).

I cleaned the area with compressed air and used a cotton bud to take out any extra debris. All was going well until I tried replacing spark plug number 5. It went in easy for the first 3 turns then started to resist being screwed in. I didnt push any further - took the plug out and checked the thread. Nothing was wrong with it. I then looked at the old plug to see if the thread had been damaged on that one - no damage. So I left it for the week.

Came back this afternoon. Had an idea to use some engine oil to lube the thread and see if that screwed in anymore.

Same resistence after the third turn - only when I took the new plug out this time - there was slivers of metal that came out in the new plugs thread :D I then put a cotton bud down the plug hole to see if anything else would come out - a tiny bit more of metal came out :(

Obviously this is a very bad sign. So I'm stopping all work on my car as of now and calling Marty on Monday. I need some opinions from you guys/girls on how serious this may be. For example: Do I need a new head? or is there anyway chance of saving the current head on my engine?

Any helpful comments would be great. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/220670-spark-plug-change-issues/
Share on other sites
black_gtst Proficient

black_gtst

Posted
Posted

hmmm that a bit of a boo boo! i dare say pulling the head off and re-tapping the thread will be the way to fix. few hours involved though. As for new head, i doubt it man its just a matter of cleaning up the thread. im sure your not the first one this has happened 2!

R33S2 Grand Master

R33S2

Posted
Posted

Its hard to say without looking at it, but you wont need to replace the head, just retapping the thread will fix it, the worst that can happen is it may need a helicoil but i doubt it if you stopped when it got too tight.

Fry_33 Proficient

Fry_33

Posted
Posted

I had a cross-threaded spark plug in my old VK commodore. One of my work mates at that time was a mechanic and carefully used some thick grease on the tap and any swarf created was caught by the grease.. Well being realistic, the majority of it I guess, no way of really knowing though. TIt was all good after that. Just an alternative that may save you some time. Good Luck

black_gtst Proficient

black_gtst

Posted
Posted
Thanks for you reply black_gtst.

So re-tapping the thread should fix the issue even if it seems like the existing thread is breaking to pieces?

i would doubt the origionl thread would be breaking apart but i guess anything is possable. if you are confident doing it yourself pull head off and take it 2 someone. worst case they will drill it out, put a sleeve in it ans then tap a new thread. a custom engineering place should be able to sort it out for you. as i say bit of stuffing round but prob no need for a new head.

hope this helps you out, im sure someone that has had the same problem will post up!

brett

halomansion Contributor

halomansion

Posted
Posted

ye its terrible when something like that happens.at least you were careful etc.it is usual to retap a thread but get someone good to do it so you get a good thread.it might leave some debris in engine from retap so perhaps consider that.dont know what caused it to thread.probably just a bit of wear and tear.i think some times the plugs may vary a bit and it is very unfortunate.

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

I watched one of the mechanics where i used to work fix a similar issue.

Step one: find the appropriate tap for the thread.

Step two: smother the tap and thread in the head in thick grease.

Step three: gently clean the thread by running the tap through.

Step four: using ear cleaners, clean the thread out and make sure its clean.

He then did something I thought could be useful in all sorts of circumstances.... He had a small vaccum line (like the ones all over the engine bay). He tapped it up to the end of a vaccum cleaner and then proceeded to vaccum the cylinder out...

Step Five: Vaccum the cylinder out!

The car that i watched it on went fine... and the plug threaded in nice and easy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      Welcome back brother 
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...