Jump to content
SAU Community

Recommended Posts

Here's what I still got up for sale

Will upload more photo's when I get an opportunity to take em.

S15 rear 5-stud conversion and brake setup, contains calipers, rotors, uprights, hubs, cables and hoses. Fantastic condition, came from a mint s15 with very low km's. Factory pads got massive meat and rotors are barely worn although rusty. Perfect for those chasing a 5-stud conversion without going drum brake setup - $350

IMG_0712.jpgIMG_0713.jpgIMG_0714.jpgIMG_0715.jpgIMG_0716.jpgIMG_0717.jpgIMG_0718.jpg

HKS sequential BOV on Hotpipe for R33 GTS-T - $150 Delivered /will fit straight onto R33 GTST or can salvage the adaptor from the pipe and weld onto any hotpipe or intercooler pipe on any turbocharged car provided piping is aluminium.

R33BOV001.jpg

RB20DET 80mm AFM (good for up to 220rwkw) + Blitz SUS Pod filter - $150 Delivered

RB20DET80mmmafandBlitzSus.jpg

444cc injectors from R32, R33 GTR Skyline, RB26 DETT - $250 Delivered

R32R33GTRRB26Injectors.jpg

Stock R32 GTS-T RB20DET Manual transmission ECU - $150 Delivered Sold Pending payment

RB20DETManualEcu.jpg

2 Pair-sets of foglights, one in pure brilliant white, and one in amber. Great working condition, almost regret getting an aftermarket front bar as I can no longer use these. They work fantastic (they'll take out an eye if you angle them up) - $80 a pair

Mypics228.jpg

Mypics229.jpg

Mypics230.jpg

Mypics231.jpg

Mypics232.jpg

A complete front bar for a Nissan Nissan 180sx SR model with teardrop indicators in factory green, also has foam backing, headlight brackets and underskirt. A small kink on the undermouth lip, but easily straightened with a heat gun - $100

A damaged front bar (damage on drivers side) with undermouth lip removed for a fmic, damage can be repaired with an abs welding kit, one teardop indicator (passenger side) - $3.22

Great condition pair of S14 front seats, clean as a whistle, no rails - $200

S13 front and rear brake setup. Contains calipers, rotors, hubs, uprights, hoses, cables, and front lower control arms. Great upgrade for ca18, came off my car in perfect order - $200

R32GTR Brake Master Cylinder, could do with a clean, other than that, great working condition - On hold

Most prices are negotiable

Pm me

Phillips

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...