Jump to content
SAU Community

Recommended Posts

Hi Peeps,

This months meet up has been changed slightly as stated in the old thread.. Speedracer isnt showing at the drive in's yet

So instead of missing this months meet..lets just go out to dinner and have a social evening instead :)

Date : 27th June (Friday Night)

Time: 7:30pm

Destination: The Outback Steak House

2A Hollylea Road

Leumeah

http://www.outbacksteakhouse.com.au/home.htm

Important: Peeps, please let me know asap so I can book a table!

Whos in?? :):)

Thanks Jess

Link to comment
https://www.sau.com.au/forums/topic/223652-southerncampbelltown-meet-up-thread/
Share on other sites

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

yo.

im interested.

do they have vege dishes?

Yeah they kind of do...salad and pasta dishs and might have a buger..click the link and suss out the menu I am sure they will do something for you!

Do you eat fish or chicken Shane?? I have just known some Vegetarians that do :)

ah k sweet.

thanks Jess....im full vegie....except for mcdonalds hahaha.

meet at bunnings again?

if i cant make 730 ill meet you guys there...bloody trains never run on time!

Hmmm not driving to bunnings to drive all the way back to c'town.

I say meet at the place, cause its close to my house.

Jay this is the friday before the 2nd MRA round which I put you down to be my bit bitch for the day.

ah k sweet.

thanks Jess....im full vegie....except for mcdonalds hahaha.

meet at bunnings again?

if i cant make 730 ill meet you guys there...bloody trains never run on time!

haha exception for maccas :)

Guys we will meet at the restuarant its very close to leumeah station and just behind Hungry Jacks and Red rooster!

Can we get a few of the old peeps out to this dinner...

Will book the table this week:

Sinful

Risking

Jazzy_i

Shane666

cracksta

jeffworld2

Hmmm not driving to bunnings to drive all the way back to c'town.

I say meet at the place, cause its close to my house.

Jay this is the friday before the 2nd MRA round which I put you down to be my pit bitch for the day.

Yeah I know, looks like I'm crashing at your house again.

so we just having dinner? im getting busier i need to know what we are up to

plus can we go to wakie again soon>

Blacktown Drive in are only showing times for Tuesday and Wednesday :) I will ring to see if speedracer and the other movie will still be showing friday night.

Drive in's start at 7:30pm and it's a double feature.....I am still up for the drive in...

I am also up for Wakie maybe go to an open day in July for our meet up????




  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...