Jump to content
SAU Community

Recommended Posts

I was driving the car through a mountain section of road one evening through the week and the car was making really good [too much for stock turbo's] boost. say 1.15bar. then i pulled up at the next set of lights. as i accelerated away from the lights the car felt really doughy. it was not pulling more than about .7 bar of boost. this continued and i wondered what was wrong. on the way home, i put the car in 4th at low speed and heard the turbos spool up [much louder than i normally do]. i figured i had a small crack in a hose or something.

Then this morning i drove the car again.... Made lots of boost around 1 bar and i put the foot down in the lower gears about 5 times.. all perfect! on the second to last lot of maximum acceleration in made 1.19 bar!!! Then it did the same thing again and boost didnt want to go over .7bar. i doesnt sound today like there is a cracked pipe though [no excessive noise from the turbo at all?!?!?!?!

If anyone can help me identify what the problem/solution is that would be great. is it a faulty actuator/cracked pipe/ecu drama/safe mode? who knows??? you guys do, thats why im here!!!

Link to comment
https://www.sau.com.au/forums/topic/226680-34-gt-r-boost-issue/
Share on other sites

Mate sounds like Rich and retard mode, do a search, basically your ecu knows its runing either too much boost or AFM maxing out and retards the timing and maps to safer levels.

Thanks mate, how would i know if this is the case?? Im not sure the cars output is enough to max out the afm though???

dude for some reason my car did that too at the beginning, even with my ebc it seemed to jump around abit.

using some logic from science gas laws, specifically that a gases pressure directly relates to the force of the container the gas is stored in.

in certain gears the engine is sucking in more gas and hence will lower the measurement of boost, in lower gear with less engine requirement, the whole intake system is pressurized more due to the force exerted back on the gases reading higher boost.

the gtr mfd only registers the highest boost recorded before the bov and wastegates can stabilize the pressure

dude for some reason my car did that too at the beginning, even with my ebc it seemed to jump around abit.

using some logic from science gas laws, specifically that a gases pressure directly relates to the force of the container the gas is stored in.

in certain gears the engine is sucking in more gas and hence will lower the measurement of boost, in lower gear with less engine requirement, the whole intake system is pressurized more due to the force exerted back on the gases reading higher boost.

the gtr mfd only registers the highest boost recorded before the bov and wastegates can stabilize the pressure

Yeah true it only stores the peak boost figure, but it does show instant boost pressure and generally speaking it will peak at a bit over 1.1 then it will flicker around 1 bar through the rpm range. but since this infrequent strangeness has occured it will only peak at .7 and flicker around that region. like i said its not all the time and its only just started to happen. Im still none the wiser???????? Any more thoughts Johnny or anybody?

Yeah true it only stores the peak boost figure, but it does show instant boost pressure and generally speaking it will peak at a bit over 1.1 then it will flicker around 1 bar through the rpm range. but since this infrequent strangeness has occured it will only peak at .7 and flicker around that region. like i said its not all the time and its only just started to happen. Im still none the wiser???????? Any more thoughts Johnny or anybody?

I dunno ben, bit stumpt now as my car does/did it too.

personally, my ebc is tuned for .85bar but makes .97 bar. strange huh?

do you have an ebc man? maybe take it to a tuner and get a dyno run to check boost in all gears

I dunno ben, bit stumpt now as my car does/did it too.

personally, my ebc is tuned for .85bar but makes .97 bar. strange huh?

do you have an ebc man? maybe take it to a tuner and get a dyno run to check boost in all gears

Just drove the car home, made 1.15 bar peak then 1.1 bar consistantly. no problems whatsoever. it seems that it only happens after it over-boosts. given that i think it must be a safe mode on the ecu. any thoughts???

Im with you ben, still confused as mine did it again yesterday.

im going to buy a new ebc and run it on the dyno again to fine tune everything as im too paranoid to give it the beans now.

Please keep me updated with yours and ill let u know of mine, goodluck mate.

Im with you ben, still confused as mine did it again yesterday.

im going to buy a new ebc and run it on the dyno again to fine tune everything as im too paranoid to give it the beans now.

Please keep me updated with yours and ill let u know of mine, goodluck mate.

Thanks mate, will do!!

I had a similar situation with customers R34. On the dyno makes 1.2 bar, drove it on the street 0.7....finally realized it had the ARC radiator deflector plate so hardly any air wasn't going into the airbox. So we removed the bottom section of the airbox which now grabs air through the fender...all sweet.

I had a similar situation with customers R34. On the dyno makes 1.2 bar, drove it on the street 0.7....finally realized it had the ARC radiator deflector plate so hardly any air wasn't going into the airbox. So we removed the bottom section of the airbox which now grabs air through the fender...all sweet.

ohhh, mine has the arc deflector as well, what a cowinkedink.

I will try that or mayb get a pod kit!

thankyou

-Johnny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...