Jump to content
SAU Community

Recommended Posts

not to be just another "boo hoo i got a speeding fine cause i am a moron who drives like i stole it"

but, just now i was in Bunbury, on the way in i was pulled over by a police man with a wavy red glow stick

(who totally looked like something out of Counterstrike) "we are from the Gang Task Force and you have been pulled over for a random drug and alcohol test" he says

no concern to me, been doing neither - as they were taking a swab an officer came to my car holding a walkie talkie and tells me that they are now going to book me for speeding

i was like "oh man, is it 50 along here, i swear its always been a 60 zone?"

a nerdy looking officer steps up to the car (with this vest that had like SO many pockets it was almost stupid) and shows me some hand held gadget displaying 81km/hr

glaring at me on a big red screen

"you were doing over 80... you are the only car on the road" he says

but i was only doing 60, me thinks

as EVERYONE on here knows there is a fair bit of difference between 60 and 80 kilometers per hour

...maybe 63 if my speedo is out, but 81!? absolute crap

nothing i could do - they book me and my passenger reads that they have only stung me with $150 fine and 2 demerits

count my blessings on a shit situation i guess

PS:

okay maybe a bit of a boo hoo, just feels like i have been screwed because a bunch officers in SWAT gear are bored of a saturday night

Link to comment
https://www.sau.com.au/forums/topic/226881-sw-adventures/
Share on other sites

I got done for speeding a while back on a hand held, I was so surprised when they flagged me down out a group of cars and showed me a screen that said 81km/h when I was 100% sure I was going 65 in a 70 zone because a car coming the other way flashed me, and I knew exactly where they were (they're at the same spot a few times a week).

I had a chat with the guy and essentially he said it's my word against his in court, and he believes I was going 81 (even though I was behind a bus that would have been going less than 70 too). So I had no choice but to pay up and watch them strip me of another point. :banana:

Link to comment
https://www.sau.com.au/forums/topic/226881-sw-adventures/#findComment-3994801
Share on other sites

God that would suck happen to me i was doing 40 in a 50 zone they pulled me over for my BOV was to loud even tho it was my screamr pipe i played along with it other wise ill get a Yellow plus Towed Plus much more so took the 150 n 3 points and Now i got No lincse lol

Link to comment
https://www.sau.com.au/forums/topic/226881-sw-adventures/#findComment-3997129
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Thanks for that mate always a good help
    • It's not really a calibration issue, if the voltage is really at 2V. If the voltage is 2V, then that's what the TPS is putting out, and the Haltech is seeing that and 2V is about 40% open (you know, between 0.45v being closed and something close to 4.5V being fully open). So, that would suggest that the TPS is maladjusted, on crooked, something something something. Or a wire problem.
    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
×
×
  • Create New...