Jump to content
SAU Community

scariest night of my life

DJ_L3ThAL

By DJ_L3ThAL,
in Victoria

 Share

Recommended Posts

NismoR34 Grand Master

NismoR34

Posted
Posted

I am sorry to hear that Nath.

I also agree with 'everyone elses' comments but I would like to add that you can NOT control what other people do on the road so whether you are going slow or fast doesnt always matter.

You just have to do the best you can and hope that other road users do the same :)

Dale.

Ronin 09 Grand Master

Ronin 09

Posted
Posted

Nath, thats some bad s*it. At least everyone is A-OK and no one was injured. There is a time and place for speed, and public roads are not it. I'm not saying i'm some sort of road angel - everyone has days where they sink the clog a bit - but always stay well within your ability. As a young P-plater, i did some really stupid stuff behind the wheel, and it is a miracle that there was never any human injury.

Unfortunately, as Dale has said, you can't control what other ppl are doing. We went up to mile high last night (by coincidence, and ran into some of the boys), and the number of ppl flying down and up the mountain was amazing. My mate took my car up the mountain, and at some places he would have been doing a-dollar-twenty. Now i trust him - he has track experience - but what happens when someone doing the same coming down the mountain loses it? You don't even want to think about that sort of stuff, but you have to remember that though you can't control other's behaviour, keeping yourself safe is the most important thing.

BTW, if this rambling doesn't make sense, its because i appear to be quite intoxicated at this point... and i have work at 8 tomorrow morning. Hurt-locker here we come!

Be safe, ppl :)

Chef_32 Mentor

Chef_32

Posted
Posted

Kinda funny how everyone with a fast car makes fun of rice until they crash. There are better ways of showing off your car than leaving marks all over the road. Blood on the road aint a pretty site, especially if there are skid marks preceding it.

Drive Safe Victoria

predator Grand Master

predator

Posted
Posted

He wants something faster? hmmm, I thought he had learned his lesson? But then again, the same thing can happen on any car. So many people lose their lives in similar situations. That black ice stuff is very dangerous, you don't know its there until you are sliding across it, and there isn't heaps you can do.

In a way I'm glad I drove a lot of slower cars over the years before my current car... learned so many things and made all the usual mistakes that may well have been amplified by a lot more power ontap. In way that is why cops pick on p-platers in skylines, especially if you have done any modifications. People can bitch and winge about it, but there are reasons why they pull p-platers over in skylines and the like -- and a lot of the time it is to save YOUR life.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Stock Airbox and Snorkle for RWC - VIC west

      By PranK · Posted

      Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • PranK
      Duncan's V37.......race car?

      By PranK · Posted

      This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...