Jump to content
SAU Community

Recommended Posts

Hey,

Ive given a search through the rb20 thread, and there doesnt seem to be a lot of information in regards to a rb20 hiflow turbo.

Slide used to sell them, but cant find the old thread with the specifications and power rating...

Would anyone know the power rating of the rb20 hiflow on a r32 rb20?

Would the rb20 hiflow be able to reach 200kw atw?

From what i have gathered;

rb25 std turbo on r32 = 180-190kw atw~

rb25 hiflow on r32 = 215-220kw atw~

Would the rb20 hiflow fall in between at around 200kw atw?

Thanks

Patrick

Link to comment
https://www.sau.com.au/forums/topic/227220-power-rating-of-rb20-hiflow/
Share on other sites

Hey,

Ive given a search through the rb20 thread, and there doesnt seem to be a lot of information in regards to a rb20 hiflow turbo.

Slide used to sell them, but cant find the old thread with the specifications and power rating...

Would anyone know the power rating of the rb20 hiflow on a r32 rb20?

Would the rb20 hiflow be able to reach 200kw atw?

From what i have gathered;

rb25 std turbo on r32 = 180-190kw atw~

rb25 hiflow on r32 = 215-220kw atw~

Would the rb20 hiflow fall in between at around 200kw atw?

Thanks

Patrick

Here is a bit of info on some RB20 & RB25 hiflows

Click Here

With the RB20 hiflows it might be a push with the Satge 1 but the Stage 2 & Stage 3 will be able to get you there.

Stage 1 RB25 hiflow will also be able to do the job.

Regards,

Ricky.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...