Jump to content
SAU Community

Anyone have a screamer pipe??

Lozza150

By Lozza150,
in Engines & Forced Induction

 Share

Recommended Posts

EVOIV Community Regular

EVOIV

Posted
Posted

What I would like to do with my next car is have the wastegate pipe exit off to the side of the car, just like Top Secret's Supra. Then you would be able to see flames :) Most of the wastegate pipes just dump to the ground, and are underneath the car so you can't see the flames, just hear the bark. I guess the wastegate pipe is just like an exhaust without a muffler. The sound probably depends upon the specs of the turbo? I don't think it's affected by the wastegate, because after all it just acts like a valve.

Good choice on the manifold GTS-t VSPEC, hope everything goes well. Should be interesting to see the results. Just a question, when peope custom make manifolds, how do they decide the shape? Do they equal tune/length the pipes of the manifold? Or do they just make it up? I thought equal tuning would be important - to have a constant pressure througout?

Steve Grand Master

Steve

Posted
Posted

I have a trust type R, which is plumbed back and is reasonably quiet. In fact just about everything is pretty quiet (except the screamer), the exhaust definately is louder with new turbs/manifold but has a really nice note to it, much angrier sounding, but the pod noise is completely gone with the new box.

Evan made my RB25 tuned length ceramic coated mild steel manifold for 1200, ceramic coat of manifold and dump was around $200.

EVOIV Community Regular

EVOIV

Posted
Posted

Sounds good Steve. Is the "quiet car" so as not to attract unwanted attention? Eg red and blue lights. That's probably a wise thing. I find it very discouraging if cops are out there and defecting a lot of people. All your hard work has to be ripped off. What a pain! Hope it doesn't happen to anyone, but I'm sure many people here have already had the unpleasant experience.

  • 3 weeks later...
Jimbo2000 Grand Master

Jimbo2000

Posted
Posted

right, wasnt sure as i'm looking into picking up a turbosmart ultragate or something similar,

heres my problem, not making any difference from 14 psi and over,workshop thinks its cause of the wastegate (T04) it had 2 "bedsprings" hanging off with one attached to the turbo and one not, due to the seller of the car taking it off so i wasnt learning how to drive it with it pushing out close to 1.5bar

thought it was a restrictive cat but later found out that it was gutted anyway, so replaced that with a 3 inch and still the problem remains.

any suggestions?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      Biggest thing is you're okay!   It sounds like between the accident, and the drive home, it was a pretty torturous trip again! On the bright side, you took the opportunity to enjoy the event more from the perspective of a spectator, than as an entrant!   Sad to see so much damage to the car. It really has taken a HUGE hit in the front end. If/when you choose to repair, hopefully the rails are straight (At least from shock tower backwards). Hopefully the extra cage coming through there has save most of the chassis rails, and HOPEFULLY saved the motor too. Best of luck when you eventually get motivated to start pulling it down to check it all out
    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Sounds more like what Brad said, that it's mainly transfer. What pad bed in procedure did you use, and did you replace/machine the rotors, or just swap pads?
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      The stutter is almost entirely in the pedal. I don't feel the brakes release and reapply as you would with ABS engaging but the pedal feels that way, without the brakes releasing. It only lasts for less than a second and the pedal is fine again. It's hard to explain, sorry.  I'll get under this weekend and just double check everything is tight. Fluid is at max where I left it.
    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • bcozican
      R32 Gtst - Track Car

      By bcozican · Posted

      Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
×
×
  • Create New...