Jump to content
SAU Community

Recommended Posts

Im not going to lie, i have very minimal knowledge of importing cars.

With that out of the way i have recently been trying to research the topic.

Im on the market for a new car with a total budget around 26k and initially not many cars that were in my price range grabed my attention locally.

Then i began looking at imports and have become quite excited at the prospect of importing a V35 coupe.

Iv checked multipule sites including J-Spec (Much talked about on these forums) Imports101, Prestige Motorsport ect ect

Prestige motorsport seem to generally be giving lower prices for a landed and complied v35. With many examples between 20 - 22k.

Can anyone advise me if they are reputable company or not? Would they be giving lower quotes for a bad reason?

These are a couple of recent examples they have showed me:

http://www.prestigemotorsport.com.au/modul...hp?StockID=4675

http://www.prestigemotorsport.com.au/modul...hp?StockID=4673

Both of these cars are estimated at under 21k landed + complied.

Im bassically wanting to know if Prestige are a reputable company?

Also if anyone has managed to recently import a v35 for 25k or less landed and complied?

Does 26k seem like a budget that can get this done? or am i dreaming?

I really appreciated any you guys can offer me.

Regards.

Edited by Kile

Please note that if two brokers are charging near enough to the same service fee then their landed and complied prices will be the same assuming they are quoting realistic prices with accurate exchange rates, shipping costs and compliance rates ... just to clarify, we under estimate the exchange rate because no banks give you the full wholesale rate advertised, we over alll slightly for shipping and don't list the absolute cheapest compliance price usually so there is a very good chance of it costing slightly less than the estimate as long as rates don't change heaps or any unexpected costs pop up ... also keep in mind that we have many customers looking for these cars who are signed up with deposits in place, so the best deals are always gone before they make it onto the website anyway.

With regards to your desired car, a budget of around $25,000 landed and complied should be very simple to get a good V35 these days, you should be able to fairly easily get one for around $20,000 to $24,000 as long as you are not looking for a 2006 model in black with 6 speed manual and Brembo brakes or a limited edition 70th Anniversary model ... the examples you showed above are fairly typical of what you can get from auction these days if you are an active client and bidding on cars, we have had a number around this price but as noted above they are all sold before hitting the mailing list.

I would be happy to also show you examples if necessary or actually help you find a car if you are ready to buy?

I'm currently going through Prestige Motorsport for my import, Geoff has been extremely helpful and informative. I'd highly recommend him based on my experience so far.

That being said, don't get me wrong, I have nothing against J-Spec. I've heard good things about Craig from friends who have been through the same process. It was just unfortunate that when I was ready to buy, J-Spec were going through a busy patch and couldn't get back to my query in time so I decided to go through Prestige.

I think with both of these companies, they'll be quoting realistic prices as it's not in their best interest to underquote. They gain their reputation through customer experiences and feedback and the only way to keep a customer happy is to be as helpful and accurate as possible.

Craig i really appreciate your detailed response. I am currently in the process of moving residence so i will be waiting a month or two before starting the process. Although i can say once i am ready to get the ball rolling you will be on the top of my list to contact.

UnCo thanks also for your informative and genuine post. Much appreciated.

:P

Kile

Oh, sh*t, too late...umm....

Please note that if two brokers are charging near enough to the same service fee then their landed and complied prices will be the same assuming they are quoting realistic prices with accurate exchange rates, shipping costs and compliance rates ... just to clarify, we under estimate the exchange rate because no banks give you the full wholesale rate advertised, we over alll slightly for shipping and don't list the absolute cheapest compliance price usually so there is a very good chance of it costing slightly less than the estimate as long as rates don't change heaps or any unexpected costs pop up ... also keep in mind that we have many customers looking for these cars who are signed up with deposits in place, so the best deals are always gone before they make it onto the website anyway.

With regards to your desired car, a budget of around $25,000 landed and complied should be very simple to get a good V35 these days, you should be able to fairly easily get one for around $20,000 to $24,000 as long as you are not looking for a 2006 model in black with 6 speed manual and Brembo brakes or a limited edition 70th Anniversary model ... the examples you showed above are fairly typical of what you can get from auction these days if you are an active client and bidding on cars, we have had a number around this price but as noted above they are all sold before hitting the mailing list.

I would be happy to also show you examples if necessary or actually help you find a car if you are ready to buy?

:P:( :(

My only advice would be bid at auction. That stock shown is usually sitting in a car yard, so the dealer has already bought the car at auction, put a mark up on it - then sold it to you.

For my next car - i'm going to Japan to find it.

Edited by paulR32gtr
My only advice would be bid at auction. That stock shown is usually sitting in a car yard, so the dealer has already bought the car at auction, put a mark up on it - then sold it to you.

This is true most of the time, but there are some dealers (well more export agents) who buy from auction and put only the standard FOB fee on top that you would be paying if purchased from auction anyway - this effectively saves you the time and hassle of checking dozens of cars to find a good one and then try to buy it cheap. They check out cars and bid low amount all day every day so the ones they get are the better cars at the better prices which are often better than you will normally get from auction ... this is only the case for the "good" agents but obviously these are far outnumbered by the dodgy ones who just want to make huge $$$

Also there are such things as wholesale dealers who offer us cars at below market value and then move them to auction if they aren't sold within a few days. These cars are normally cheap enough that about 75% or more of them will sell for more than the wholesale price if they end up at auction. This is just one more way that you can get a better deal without going to auction.

The reason I mention this is that there are a LOT of people out there who just don't want to buy from auctions, either they don't want to make a decision about bidding and budgets within hours of first seeing it with only a few photos on which to base that decision, or just want/need more information than can be obtained from auction cars in a given time ... these people really need to buy from dealers or other agents so they can get more photos and details and take a few days to decide on the purchase, so there are different options for different people depending on with they require to make them comfortable with the process.

For my next car - i'm going to Japan to find it.

This would also work if you are not looking for anything too specific, but if you are looking for a less common vehicle or combination of colours & features then you may not find it by restricting yourself to one city or region of Japan by being there in person ... often you can find the car you want more easily, faster and sometimes cheaper by being able to cover ALL auctions and dealers around all regions of Japan at once which can be done just as easily from your computer here in Australia as it can by being in Japan in person.

  • 1 month later...
  • 4 weeks later...
  • 4 weeks later...

geoff at prestige is the man he helped me for 5 months to find the right 1971 kgc10 skyline...it was worth the wait. he had around 30-40 cars inspected for me and scored me a gem. Help me thw whole way through the process. I still email him now for a chat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...