Jump to content
SAU Community

Completed Hicas Diag... Bad Speed, Angle, Neutral And Clutch Sensors!

joeleo87
 Share

Recommended Posts

joeleo87 Experienced

joeleo87

Posted
Posted

hey all, as title states ive completed the diagnostic for the hicas and got those results.

bad:

speed sensor

steering angle sensor

neutral postion sensor

clutch sensor

what are my options?

cheers joel

heller44 Mentor

heller44

Posted
Posted

Considering fairly much all that stuff comes from your dash area, look for wiring that has been played with.. Also check that you have a good connection onto the hicas module itself and any connections in between.

I only had the steering position sensor working out of that list when I started fixing faults, and even then the pricks had cut the harness back from the power steering solenoid anyway..

heller44 Mentor

heller44

Posted
Posted (edited)

kneejerk response.

I really do like the speed sensitive power steering, without the hicas system working you don't get this. I found it easier to spend some time and work out why it isn't working and fix it, rather than rip it out and have to live with a non functioning system, building a module for proportioning the power steering without the hicas module, or having to swap in a steering rack from a car without the speed senstitive steering.

It isn't hard to work out the wiring, r32 wiring diagrams are reasonably comprehensive.

By all means lock the rear in place after fixing the issues if you don't like hicas, but I feel that getting the power steering working first would be a better idea.

Edited by heller44

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...