Jump to content
SAU Community

Recommended Posts

Ok guys,

Just an updated thread, because the other one was what, 11 pages?? And if someone is going to want to come on my cruise they aren't going to want to sort through 11 pages of crap :D haha.

So.

Cruise this Sunday, August 17th.

Meeting at 1pm, at Tennyson.

Heading South along the coast, making a few stops in between where I'll be taking photos of the beasts lol.

And finishing up at Maslins Beach (no getting nakie :P)

If you haven't already received the route details from me, send a PM my way with your email, and i can email the route details to you, as they are in a word document :D

Also, if you ARE coming, could you please just write a short post on here to let me know, so then i know what sort of numbers to expect.

Cheers for that guys!! Can't wait :D

-Charmaine

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

Hey will be there with R33 and hopefully a cefiro, if not many cars come ill con my boyfriend to bring his R32 for ya. hope it a good turn out, to help ya with yr 12 studies! every car helps. xoxo

Bit of both lol. Even if it wasn't for my yr12 photography assignment, i'd still organise it for a bit of fun and so i could take some photos :D

illl be there if my sat night out drinking is only as late as this 1 :D

should be good to cruise though.

^^ cancel gtr boys only i may roll in the R :D

and norm if you lucky ill let ya roll in my car cause im a nice swell kinda guy :P

can i be the first to say what the f is Tennyson that a shop suburb or what?

n maslins hasnt been a nudie beach for quite a while, no i dont know from experience i know people that live a few k's from there

Edited by Inline 6

can i get the cruise notes pm'd to me?

i dont think i can go on the cruise but i dont live far from the final meet spot as im a southy so could prob meet then

Edited by Import S13

i dont even know where the hell that meet point is...

... ill be there though... depending on how f**ked i feel after work tonight... shoot us a pm anyways.

I'm going to have to bail!

Last night, I noticed a drop in oil pressure, so I pulled over, checked my oil and found I had lost 50% of oil in only a week. Drove around the block, had white smoke pissing out the exhaust. Stopped, checked oil again and had lost even more oil!

There's no knocking or strange sounds, still revs smoothly right up to 8k and it still pulls hard.

Thinking it's the rings or turbo oil seals - more likely the oil seals, as at high boost ever since I had the car I've had a small amount of white smoke coming out, but only at high boost. It's been doing that for a good few months, so now I think it's finally given way! Car will be off the road until mid-October now due to lack of funds! I'm not happy at all.

I've booked it in @ Boostworx so I can get a compression test to make sure it isn't the rings. It doesn't sound like a rex, so I haven't dropped a piston either!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...