Jump to content
SAU Community

Urgent : stalling problem

Craved

By Craved,
in General Maintenance

 Share

Recommended Posts

Craved Grand Master

Craved

Posted
Posted

Hey people,

Have myself a large problem, well large for me :D

When the car starts it will run for about 5 seconds then stall, if you increase the revs and hold at a certain level the car will still stall!!!

has new spark plugs, and starts fine!

bear in mind that the car has not been started in 3 months was wondering a few things, would this be caused by:

A) removing the stock solinoid eg unplugging it from ecu

B) fuel filter drying up and not allowing fuel through

C) dirty airflow meter - how do it clean?

D) suggestions please

thanks fellas, dying to drive her again :D

Link to comment
https://www.sau.com.au/forums/topic/23434-urgent-stalling-problem/
Share on other sites
WazR32GTSt Grand Master

WazR32GTSt

Posted
Posted

sounds like its something that directly affects the way air/fuel is measured.

so i'd say maybe a leaking inatake hose that is causing a loss of air, or a dirty AFM (do a search for how to clean), or an afm that's unplugged or something?

does it blow a puff of black smoke when u start it?

T88 ON BOARD Mentor

T88 ON BOARD

Posted
Posted

If the car has an Alarm system that runs with its own Battery and has the power to cut of Fuel then u need to buy a brand new car battery then connect it to a charger and charge it for about an hour to give power to the alarm battery...

This is a common problem with Those kind of alarms....

Otherwise you could have a mechanical problem of some sort..Get it checked out

Craved Grand Master

Craved

Posted
  • Author
Posted

yeah, just got a new car battery as well!!!

i know what your saying though, but it wouldn't start at all would it?

this thing runs for a couple of seconds then drops off, and only if left for a while!!!

it's at a mechanics now, hope fully to pick it up today!!!

had a mad run of bad luck!!

had a bloody window fall out on the way to the mechanic's today, bloody sikaflex must have gone off and not actually dried!!!

so thats an extra $300 to get this replaced then get it tinted again!!! AAARRRGGGGGGHHHH.......

well maybe something will go right for me :)

maybe

Craved Grand Master

Craved

Posted
  • Author
Posted

WazR32GTSt

Yeah thats much better, whats even better i have the car back now, running like an animal!!

it's amazing how much faster they get when you dont drive them for a long time :D

anyway turned out to be slight corrosion on the points of the ecu, and fuel pump relays!! had these cleaned up and it started, running rough though!! cleaned the AFM, then had issues with the calibration of the idle controller (no changes prior to incident) and it idles sweet now, although the revs dont drop after being in neutral for a couple of seconds like it used to!!

But hey, im still and extremely happy man, just gotta take some photos and post up the new paint job, now that it's all back together.

thanks for the responses people!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • tidi0x
      R33 GTST Axles

      By tidi0x · Posted

      The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Potentially some interesting data for some of you here; Hank Iroz from Iroz Motorsport testing a new Xona Rotor 5964S on a Audi RS3 2.5L DAZA motor. https://facebook.com/share/p/14EU18MyDqZ/ Cliff Notes: Turbo has the new Xona XRE compressor aero with an X4C compressor cover, reportedly 0.64 rear housing. 900whp (670kw) @ 37psi, 170k shaft speed, motor is making 2bar (29psi) boost by roughly 3800rpm, 500lbft (670nm) torque by 3500rpm. They overlaid a stock RS3 on USA 91 fuel (red), and a "Stage 2" RS3 on E85 (yellow), and this 5964S (blue) - the 5964S isn't losing any ground to either. Apparently out-flowing their prior tests with a Xona 8264S (green), and this 5964S (white) also has a smaller A/R than that did.
×
×
  • Create New...