Jump to content
SAU Community

Recommended Posts

Item: Garret t04e huffer!

Age: .. about 2000k on it

Condition: VERY Good

Price: $600neg

To Fit: A car!

Location: Perth WA

Contact: 0424 193 992 (pls ring after 5pm WA time)

Comments:Turbo is in VERY good condition. Pulled it off last night. Checked it out, no shaft play, no damaged blades etc.

Compressor: .7 A/R, 4" inlet, 2.5" outlet

Exhaust: 1.15 A/R, 3" outlet

This turbo is a 60mm trim with a T4 footprint

Reason for sale is I have a larger turbo

Thanks! offers welcome!

Link to comment
https://www.sau.com.au/forums/topic/236503-fs-garret-t04e/
Share on other sites

hey mate

what car was this turbo on before and what sort of power were you making on what psi?

Definately interested also how much to post it to 5107 South australia mate

thanks

krishy

Link to comment
https://www.sau.com.au/forums/topic/236503-fs-garret-t04e/#findComment-4142827
Share on other sites

it was on a fc rx7, i managed to make 333wrhp @ 13 psi

i just got a 18kg turbo posted to me from eastern states for $53

so i guess $35 should cover it.

turbo3.75f.th.JPG

turbo4.d70.th.JPG

hmm no idea why pics are so small :\ trying to use some funky upload site

also, regarding wheel sizes, i believe they are very similar to gt35..

Edited by Jezzza
Link to comment
https://www.sau.com.au/forums/topic/236503-fs-garret-t04e/#findComment-4143803
Share on other sites

$500 for a BIGGER Garret TO4E turbo with NO shaft play, has seen a max of 13psi over about 2-3000kms!

it will be fully sick on a rb25det

proven to make 330+wrhp @ 13psi on my rotor.. imagine it on a 2.5L pushing closer to 18-20psi :mellow:

very similar wheel sizes to the gt35's btw :rant:

Link to comment
https://www.sau.com.au/forums/topic/236503-fs-garret-t04e/#findComment-4156515
Share on other sites

a few ppl been asking me what they would need to use this turbo..

I DONT KNOW! IM SORRY!

i do not know what is on your car, ot what is needed. i have given info for you to find out

Link to comment
https://www.sau.com.au/forums/topic/236503-fs-garret-t04e/#findComment-4159581
Share on other sites

  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
×
×
  • Create New...