Jump to content
SAU Community

Performance Parts For Sale

tommygr34
 Share

Recommended Posts

tommygr34 Proficient

tommygr34

Posted
Posted

Item: Garrett Turbo

Age: unsure

Condition: very good condition NO SHAFT PLAY!!!

Price: chasing around $500 make an offer want it gone to fund new engine

To Fit: was on a RB would suit any thing above 2.5L due to the size

Location: Melbourne SE

Contact: Tom on 0401035221

Comments: had big plans for my engine using this turbo with other needed parts to produce over 250RWKW but changed my plans and im going RB26 Poweraaa unsure on the exact model number intake side of the turbo reads GARRETT B.C.C. A/R .60 and in small print M33 the exhaust housing reads .86 so its a fairly big turbo 3" exhaust V-band of the exhaust housing has thread tapped in to exhaust housing for Exhaust temp sensor its is a external gate turbo oil feed only not watercooled

Item: Turbo Garrett T04E

Age: unsure

Condition: fairly good has shaft play but does not hit either side of the housing

Price:$500

To Fit: any RB T3 flange

Location: Melbourne SE

Contact: tom 0401035221

Comments: the idea behind buying this turbo was to use the exhaust housing on the other turbo i have for sale hence it being smaller and a T3 flange, turbo read GARRETT A/R.50 B.C and the exhaust reads A/R .63 oil cooled only not watercooled...it too is a externalwaste turbo i have to a external gate adaptor which goes between the exhaust manifold and turbo and the externalgate bolts to the adaptor hence the turbo sits about 1 3/4 of a inch lower so a shorter oil return line and a longer oil feed is needed if needed it would be and extra 80 bucks its brand new never been used

Will post photos on possibly mon or tues my camera is at work

Link to comment
https://www.sau.com.au/forums/topic/237970-performance-parts-for-sale/
Share on other sites
  • 5 weeks later...
tommygr34 Proficient

tommygr34

Posted
  • Author
Posted (edited)

pics

bigger turbo

DSCN3490.jpg

DSCN3492.jpg

DSCN3495.jpg

garret t04e? info as above

DSCN3486.jpg

DSCN3485.jpg

sparco seat used no rails average condition good for track car etc $150 NEG

DSCN3481.jpg

HKS exhaust housing heat sheld came of my hks 2835 pro s i have no need for it $50

DSCN3498.jpg

DSCN3505.jpg

T3 external gate adaptor new

DSCN3497.jpg

greddy SM white face gauges with controller $300 very neg!!!!!!!! NOTE NO WIRING LOOMS OR SENSORS included has plans mo make wiring loom to me it isnt too hard but may require an auto elec or someone thats good with wiring isnt that hard to do NOTE the reason these are so cheap is the no wiring loom and senson PLUS IF YOU LOOK CLOSLY YOU WILL NOTICE SLIGHT DAMAGE TO THE METAL HOUSING TO SOME OF THE GAUGES DUE TO ANOTHER SAU MEMBER NOT THINKING JUST THREW THESE GAUGES INTO A EXPESS PAIDED ENVOLOPE AND NOT PACKING THEM CORRECT HENCE ITS MY LOSS AND THERE DUMBNESS

DSCN3506.jpgDSCN3518.jpg

Edited by tommygr34
  • 2 weeks later...
tommygr34 Proficient

tommygr34

Posted
  • Author
Posted

heat sheild sold ...... external gate adaptor sold....everything else is still for sale!!!! $250 for the gauges $110 for the sparco seat....turbos $200 each!!!!!!!!!!!!!!!!!!!!!!! need it gone!!!!!!!!!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...