Jump to content
SAU Community

Recommended Posts

ok yeah this might be a place for a wanted sales forum but i dont think it will be any use there seeing as ive been looking 3 months for a set of 87mm non turbo pistons. If anyone can help me with a few places to look at it would be so much help to a skyline thats been in a driveway for 3 months with no engine.......ANY HELP

yes they need to be 87mm because i warped the bottom end (i dont know how but it isnt to but) the thing thats making me go 87mm is the scoare with the 5th cylinder, its so bad it looks like a 100 year old drain pipe, so yeah all cylinders need to be boared by 1mm now and i need help finding a set of pistons.

PLAN B

if anyone knows of a gts4 engine, its just been so long without my car ill just buy the engine and stick it in (bottom end only would be nice as i have a reconditioned top end now)

yeah so its a bit complicated for a wanted forum seeing as these parts are not your everyday parts in japan even :O

Cheers, Andrew

Link to comment
https://www.sau.com.au/forums/topic/239454-87mm-pistons-for-a-na/
Share on other sites

yeah so this was my plan C because the price is going to be really big probity.

i can wait a month or two if no stock pistons or engines turn up then i might choose hand made. The only place i know of so far that make oversized pistons for it are Nissan but they only do it from japan and Nissan Australia will not order it for us. i have the part number for the pistons.

rb30evsrb25depistonsnk9.jpg

this may help

Use rb25 pin and rods.

Looks like you will also be getting higher compression ratio with an rb30 piston.

RB30 pistons will be dirt cheap but you will also need to get new rings and a good honest clean

Edited by GTS4WD

even better, could ditch the 25 and go for a RB30 bottom end? :D. keep an eye out in the classifieds tho, i know theres a couple of GTS4 wrecks im watching that had motor and running gear etc...they tend to pop up regularly.

GTS4WD i think you might be right

im sure you can use the rb30 pistons or the rb25 pistons in a rb25/30 hybrid, so there im seeing them as a pistons for rb30's and rb25's am i not right??

anyone who can answer this with a first hand experience on the differences, it would be much appreciated. If so im going to get a good set of 87mm VL/r31 pistons and be very happy :( i have 12 rb25 pistons, and rods so im not short there :D

we looked into a rb30 bottom end but it sits ontop of the 4wd drivetrain and such theres no way it wanted to fit in there because have one in the garage and its not the gts4 block shape

thanks GTS4WD, ill get my uncle to play with the pistons and stuff and see if this option is the winner

ahh yes i found that out after seeing a lot of GTR's like this, although it would be good power being a everyday driver i think i have to keep my response in mind.

Price wise i have a few rb30's lying around in my uncles workshop some in tiptop condition :( so it would only be adapter costs.

ive even got a bottom end from a 25 thats only done 40,000km so im really set on looking into the rb30 pistons tomorrow morning ;)

so many options to choose from all at once, haahahaha :)

Edited by central coast person

Just bear in mind Andy that there is a little work in an RB30DE set up. You need to relocate a pully, use a different timing belt and tap an oil feed.

I vote (for ease of installation) that you use the 25 bottom end if you can get it for a good price because 40,00km is nothing

oh its mine :)

i brought it from a auto skyline that had a hit. I sussed it out and the owner was old family man so i didnt see him going out and racing haha and he didnt cause the crash and i didnt need much from the engine just the internals that are the same as a mannual which is almost everything. i brought it opened it and its so new i dont need to change the bearings or anything, so what ever parts need changing in the good old gts-4 will be done. except for maybe the exception of ACL racing rings which my uncle is strongly recommending and i want ACL racing big end bearings........

as you can see im wanting to stay rb25 as well because the response would be nice, seeing as im getting stainless steel air intake to shove the old plastic one out the way because i think im going 80 or 90mm throttle body, i have those dkne extractors in my skylines back seat atm waiting to go in the engine bay before that air mod though and splitfire coilpacks and just changing every maintenance part there is from fuel filter to gaskets. i dont want to get a rb30 bottom end and addaptor plate and spend money on a engine that needs to be fitted in there when i can make minor power with a lot better response.

turning into a what to do to my engine forum ayyyy

only hopes for me are the pistons in japan or the rb30 pistons, fingers crossed

hmm seeing as i was just at bathurst i have this thing for coming into corners really fast :ermm:

anyway i would have to agree because i did wreak the other engine, not from speeding just my high rev addiction.

news update on this, just ordered pistons from Nissan Japan 50thou!!!!

will keep up to date when i receive these pistons because there is slight confusion, apparently they are r32 pistons but they typed my vin and chassie numbers in and its the ones recommended so its a gamble at the moment.

yep :)

i get free four day paddock passes so i figured i should use them but im only 17 so i cant stay in a hotel or camp ground without a adult so i went saturday at 3:30am!! with my mates dad.

best stories on the way down about him being the guy who ordered and put the tires in the pits for the mark skafe r32. Hes head of Nissan mechanics now.....so he just gives heaps to my mate and me about seeing new cars and stuff everytime we talk cars. the drive down was short to it was only 2 and a half hours (almost no cars no red lights) from the coast but the trip back up was 4 hours.

got some good video's of the race from my phone and it was only 10m away from the cars so the 2mega pix factor dosnt really mater.

highlight of the day was the mini coupe with the roof but at the A pillars and pulled back to get a driver out :) it was extra mini

they are made from the standard material and are $900au

50 thou over? so a 70cc gain? I've been looking for some 60 thou over, add 100cc to my 30DE, wanted somthing a bit lighter than stock though, for a 25DE. Although in standard material you could get away with a tighter bore.

Any more info on these customs?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...