Jump to content
SAU Community

Recommended Posts

which cad program do u use shanef??

i do a bit of stuff with uni work in pro engineer wildfire

Solidworks

A complete new Pump incuding housing ?

Or just a new set of 77mm N1 Pump Gears ?

The best thing about this idea is the option of Gear upgrades for those that bought N1 pumps and don't want to get rid of them, but are scared to use them without the upgraded gears.

I am not sure if a redesigned pump would sit with enough confidence with most people.

Allan

Both. Billet pump (with external pressure relief) and upgraded gears.

if you want to upgrade your pump gears but the reimax ones. they are the best. they make the gears for group A race cars etc. formerly reinik.

http://www.reimax.co.jp/pages/products/lower-area.html

up till a few weeks ago they were about $550 too, bit more now with the bad exchange rate though. but they are good stuff. I know a few people who have used them in pumps both here and in japan with good results.

Ya, I have researched the Reinik stuff extensively and was going to go with them, from RHD Japan, till I found these. I just want more info on them.

Solidworks

Both. Billet pump (with external pressure relief) and upgraded gears.

So, basically a 'Custom' Tomei style Pump ?

What do you see the cost being for it when complete ?

Edited by JD74
So, basically a 'Custom' Tomei style Pump ?

What do you see the cost being for it when complete ?

You could say that yes. But these have bene designed form the ground up, and hanvt been based on any japenese pump

Looking at the exchange rate, now would be the time to start selling them :rofl:

hmm yes good point

You could say that yes. But these have bene designed form the ground up, and hanvt been based on any japenese pump

hmm yes good point

So what price are they going to come in at then ?

When will you have the first one ready to go ?

So what price are they going to come in at then ?

When will you have the first one ready to go ?

somewhere between 1500-2000. its hard to know the final cost before you actually get them made.

They aren't high on the list at this stage, but if there is genuine interest they could be ready to go in about 2months

  • 4 months later...
I have just recieved a Nitto pump for an engine im doing...well made item and at $1300 very competitive price wise. I see they use two roll pins peined over as extra security on the rear cover...nice.

Care to share some pics ?

Where did you pick it up from ?

Sounds like the pump I picked up ages ago. Don't know what it is, was told it was an N1 from the seller.

It has two roll pins on the rear cover too.

The housing is also smoother internally compared to the stock nissan pump (no sharp turns for the oil).

Didn't use it due to not knowing what is was. I still have it.

post-12712-1235881678_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...