Jump to content
SAU Community

Recommended Posts

Recently ive been asked about correctly degreeing camshafts in RB engines, this step by step guide will hopefully answer a few questions and allow others to understand how its done and use this method to set up vernier cam gears to find exact lobe centers.

Cam gears help you to adjust your cams so that it opens and closes at the correct time. It also insures that maximum lift correspond to a desired crank position. The center line or the point on the cam where maximum lift occurs is known as lobe center.

Setting the cams to zero on the cam gear means absolutely nothing as different manufacturers of cams and cam belts can cause exact position of lobe centres to be slightly incorrect.

Lobe centers on the HKS 264's are 110 for the inlet cam and 103 for the exhaust cam. Adjusting your cams too these specs will most probably bring them very close to their maximum designed performance . A lobe center of 110 on the inlet cam means that maximum valve opening will be at 110º ATDC and 103 on the exhaust will mean that maximum valve lift will be at 103º BTDC.

This is how I degree my cams

1. Use a pencil, paper and arithmetic for this procedure, to keep track of the results.

2. Make a rigid pointer from stiff wire or an old coat hanger and attach it to the engine block. This pointer locates the degrees on the degree wheel.

3. With a degree wheel installed on the crankshaft, rotate the crank to get the no 1- piston at TDC and check to ensure that the valves are fully closed then adjust the pointer to zero (0º TDC) on the degree wheel.

4. Turn the crankshaft opposite the running rotation approximately 15-20 degrees. Install a dial indicator above the spark plug hole (i use a flat metal plate ive fabricated that bolts to the coil pack bracket holes) with the rod of the gauge going down the spark plug hole to check the position of number 1 piston.

5. Continue to turn the engine in the same direction until the piston comes back up and just touches the dial indicator. Make a note of the exact number on the degree wheel that the pointer is on.

6. Rotate the engine in the other direction (running rotation) until the piston comes back up and touches the dial indicator. Again note the number where the pointer is.

7. Remove the dial indicator and rotate the crankshaft to the midpoint of the two marks. At this point the piston is at the true top dead center. Loosen the degree wheel and adjust it so it will read 0º TDC at the pointer. Don't rotate the crankshaft to do this!

8. Now, it's time to locate the lobe centerline relative to TDC. Attach the dial indicator on the top of the head. Set the tip to contact the top of the no 1-cylinder inlet valve shim/bucket. Check to make sure that the indicator plunger is parallel to the valve stem. NOTE - any variance in an angle will produce geometric errors in the lift readings.

9. Rotate the engine in the normal direction of rotation until a reading on the dial gauge of 0.040 lift is reached. (Valve will start to open) Mark the dial gauge and make a note of the reading on the degree wheel.

10. Continue to turn the engine in the normal direction past maximum lift. The valve will now return to its close position. Make a note of the degree wheel reading when the indicator reads 0.040" on the return side

11. Now add the larger of the two readings that you noted on the degree wheel to 180 subtract the smaller number and then divide the answer by two. Your answer will indicate the lobe center of the cam. Example: open reading was 4 and close reading was 43. Now add 43 to 180 = 223, subtract 4 =219 divide by 2 = 109.5. Lobe center is 109.5 degrees.

12. Continue to move the cam on the adjustable cam gear and redo steps 10 to 12 until the required lobe center is achieved.

13. Now do the same for the exhaust cam

Hope this is not too complicated to follow.

cheers

Paul

Link to comment
https://www.sau.com.au/forums/topic/240804-degreeing-camshafts/
Share on other sites

  • 1 year later...

Hi Paul,

In my situation I am running a RB30 with RB25 Neo head, but I don't trust the timing markings on my car for a variety of reasons.

going from what you have mentioned above and the specs for standard RB25DET NEO Camshaft duration 236°in, 232°ex lift: 8.4mm in, 8.7mm ex

does any 1 know what degree's in relation to TDC the intake cam is set to standard @ 0.040" of lift? or what degree's the intake cam is set to at maximum lift in standard form.

regards

  • 2 weeks later...
  • 3 years later...

Im running a 30/26 my exhaust cam card says at .050 should be 242 deg and intake is 253 deg at .050. does this mean in stead of

(9. Rotate the engine in the normal direction of rotation until a reading on the dial gauge of 0.040” lift is reached. (Valve will start to open) Mark the dial gauge and make a note of the reading on the degree wheel.)

I should be reading .050 and not .040

No, the mark on the dial gauge is just a reference. Really you can use any number you like, so long as you use the same number for all your measurements. So say you choose 0.040" then you just rotate the engine forward until the gauge reads 0.040" again.

Should also note that for RB's you need to preload the dial indicator due to the lifter design in a cam on bucket setup.

Yes, the 0.050" on the cam card and its documented lift refer to the lift you should see at a specific crank angle.

Between these two points is the crankshaft position where maximum lift occurs, which is also where the advertised duration measurement should be.

No, the mark on the dial gauge is just a reference. Really you can use any number you like, so long as you use the same number for all your measurements. So say you choose 0.040" then you just rotate the engine forward until the gauge reads 0.040" again.

Should also note that for RB's you need to preload the dial indicator due to the lifter design in a cam on bucket setup.

Just want to correct myself here and apologise if I mislead anyone. I re-read Paul's write up and realised he was using a different method to the one I used. My bad.

So in this case, YES set the dial gauge for the valve lift indicated on the cam card.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...