Jump to content
SAU Community

Recommended Posts

I did it myself, not really that hard, just have to pull the entire dash out.

ah okay...

to elaborate on that reply are there anything i need to be cautious of? is this process simply unplugging a few components? or what’s actually involved?

DO NOT open any air con pipes without getting it degassed, there is a lot more than you think in there, and it is quite bad for you.

once its degassed, you can remove the core in front of the radiator, the belt driven compressor on the side of the block and its large bracket to it, the hoses to the firewall etc.

In the cabin, you remove the entire dash pad and unbolt whatever you like. The fan behind the glovebox, the cooling core next to it and if you modify your coolant system a bit you can remove the heater core behind the radio too. You may as well remove all th plastic ducting etc too as it doesnt weigh much, but it also isnt doing anything once you remove the fan. You can also disconnect the control unit and clean up any wiring too. Take the fuses/relays out if you want too.

above where the fan was on the passenger side is a large hole where all the air used to come in from outside, i was running mine open and you always get a nice airflow through which is good for hot track days, but i have since made a removable cover to save my gf from the relentless wind lol.

DO NOT open any air con pipes without getting it degassed, there is a lot more than you think in there, and it is quite bad for you.

once its degassed, you can remove the core in front of the radiator, the belt driven compressor on the side of the block and its large bracket to it, the hoses to the firewall etc.

In the cabin, you remove the entire dash pad and unbolt whatever you like. The fan behind the glovebox, the cooling core next to it and if you modify your coolant system a bit you can remove the heater core behind the radio too. You may as well remove all th plastic ducting etc too as it doesnt weigh much, but it also isnt doing anything once you remove the fan. You can also disconnect the control unit and clean up any wiring too. Take the fuses/relays out if you want too.

above where the fan was on the passenger side is a large hole where all the air used to come in from outside, i was running mine open and you always get a nice airflow through which is good for hot track days, but i have since made a removable cover to save my gf from the relentless wind lol.

cool cool

very informative jeff :P might give this ago next weekend

loves the comment about the relentless wind for ya gf haha!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
×
×
  • Create New...