Jump to content
SAU Community

Head's Up All, Few Dodge Cars Hanging Around Tonight !

sven

By sven,
in Tasmania

 Share

Recommended Posts

sven Community Regular

sven

Posted
Posted

Just had 2 cars about 10 minutes ago drive past our place,

One looked to be a dark colored pulsar sedan 1998ish model with car load of chicks and skin heads.. with exhaust

And the other a maroon hatch (maybe a laser, corolla) with more skin heads in it.. Dodgy prima paint on rear bar

Drove past slowly looking at our GTR parked in the drive way, then went up the road and sat a few min's then headed back

down almost to a stop at the drive. One cut out wide and pointed my car out to the other car.

Just a heads up guy's as they might be out and about tonight for a buzz..

Cheers

ECR 033 Rising Star

ECR 033

Posted
Posted
Just had 2 cars about 10 minutes ago drive past our place,

One looked to be a dark colored pulsar sedan 1998ish model with car load of chicks and skin heads.. with exhaust

And the other a maroon hatch (maybe a laser, corolla) with more skin heads in it.. Dodgy prima paint on rear bar

Drove past slowly looking at our GTR parked in the drive way, then went up the road and sat a few min's then headed back

down almost to a stop at the drive. One cut out wide and pointed my car out to the other car.

Just a heads up guy's as they might be out and about tonight for a buzz..

Cheers

As a truck driver i see alot of skylines and imports in general everywhere i go, and i am amazed where people still park their cars at home/work etc. despite the theft rate of these things... maybe its because "it won't happen to them" or that maybe they have no other place to park them (not sure), but these cars stick out like a sore thumb as it is let alone leaving them insight with easy access.

SVEN, trying not to sound dodgy here :) but i live about 50km away from you, yet i still know exactly where you park your car along with the supra that parks around the corner from you... (again not trying to sound dodgy)... but i have come across so many imports (through delivery driving) that are left on the front lawn over night or left parked on the road over night... etc .etc.

the only way to stop them is to not make it easy for them, have it locked in the garage or behind the house or whatever.

despite insurance etc, some of us spend alot more coin on these things... than what we would ever see back from insurance payouts.

LOCK THEM UP.

and thanks sven for the heads up. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...