Jump to content
SAU Community

Fs: Nissan Stagea Series 1 Turbo Awd


MRO
 Share

Recommended Posts

For sale: 1997 Series 1 Nissan Stagea.

Condition: Well looked after. Very tidy

Price and price conditions: $12,600. Cash

Extra Info:

Standard spec RB25DET 4 speed auto AWD.

I imported this car about 2 years ago with 72,000 on the clock. The car now has 110,000. It has been my daily driver for this time and has been well looked after. It has never been boosted (factory is 5psi to 4000rpm then 7psi). I have completed a few sensible and quality mods to make it better to drive including:

- tein coilover adjustable height suspension all round. Can go another 2" lower.

- Tannabe stainless 3" cat back exhaust. Not too noisy.

- high flow cat

- JJR split dump pipe

- K&N filter

- New 52mm alloy radiator

- New PWR alloy transmission cooler

- 17" r34 Gtt rims with newish 245/35/17 tyres

- 100k service completed by C-RED including new water pump (total cost $1400)

- R33 GTST brake calipers and disks (very worthwhile updgrade)

- Pioneer CD MP3 deck with all wiring for amp and rear sub run to the boot.

The car came with a few less common features from the factory that make it better than a lot Stagea's getting around including:

- Full Dayz body kit (factory)

- all leather interior

- dual sunroofs (front and rear)

- Remote start (i dont have the keyfob to go with this)

- Rare factory airbag MOMO

- No WOODGRAIN!! Most highspec Stageas have woodgrain trim that looks like shit. This car has the grey trim that suits the car a lot better.

Contact Details: PM me here or call me (Morgan) on 0400 217 341

Location:

Perth hills in the evening and weekends.

Como during office hours

Delivery & Conditions of Delivery: COD

__________________

post-32361-1226459289_thumb.jpg

post-32361-1226459300_thumb.jpg

post-32361-1226459230_thumb.jpg

post-32361-1226459243_thumb.jpg

post-32361-1226459256_thumb.jpg

post-32361-1226459269_thumb.jpg

post-32361-1226459278_thumb.jpg

Link to comment
Share on other sites

  • 2 weeks later...
  • 4 months later...
  • 5 months later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...