Jump to content
SAU Community

Recommended Posts

have changed my setup so these parts are surplus to my needs, all are in excel condition or new.

turbosmart s13 bov pipe - $40

t28 induction pipe - $50

apexi EL2 mechanical Boost gauge - $120

alloy racing catch can - $100

2.5" high flow cat, new, made in usa - $80

turbotech bleed valve - $20

momo gear knob - $60

turbosmart boost controller - $60

tomei dump pipe 1000kms old - $200

topstage carbon fibre cold air induction kit with overflow cover suit s13 - $190

tial 38mm 7psi spring, new - $40

rb20 afm - $60

gt2871r 16psi waste gate actuator brand new - $120

straight rod actuator, brand new - $80

k&n air filter pod, never been driven on, (has slight burn on rubber due to welding of intake pipe, still seals fine) refer topics

$60

CA18 STUFF

genuine nissan head gasket, new - $70

bosch external coil setup with mount and wiring loom, new - $220

nismo 555cc injectors, top feed low impedence, fully serviced and flow tested 1000kms ago

selling as I'm upgrading - $400

low mount stainless manifold, little dirty but no cracks - $50

post-35133-1227095969_thumb.jpg

post-35133-1227095984_thumb.jpg

post-35133-1227096001_thumb.jpg

post-35133-1227096016_thumb.jpg

post-35133-1227096031_thumb.jpg

post-35133-1227096046_thumb.jpg

post-35133-1227096089_thumb.jpg

post-35133-1227096605_thumb.jpg

Edited by kizzy

Is the turbotech bleed valve the one that was going for cheap on ebay and has the massive thread dedicated to it? If it is the ball and spring type i'm thinkin of i'll take it man. If its not then what model is the turbo smart boost controller? Oh and Where do you live?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...