Jump to content
SAU Community

Recommended Posts

posted it in the wasteland, but figured id post it here just incase.

goin to take a spin in the 200. and i figured with all current controversy regarding cruises, id invite people too. come out, chillax, have a drive and enjoy. if you feel like coming along, call me up 0408961657.

:P

Link to comment
https://www.sau.com.au/forums/topic/246396-goin-for-a-drive/
Share on other sites

guh, dont you people use phones? :wub:

woulda messaged ya andrew, but well, id left before you posted..

hit *a certain road in the north*, was rather fun, first time ive driven it. definitely showed the weaknesses of the 200 mind you.

200 :laugh: that aint no skyline hope that was you refering to how much your new skyline pulls at the wheels

uh... yeah! thats right. :P

will probably be doing something tonight aswell, starting about 8-9. so if youre keen post here or send numbers via pm and start with the sms'ing. meet point will be sent to you and route will be kept off the forums.

Edited by scandyflick
when are you going? i thought youd all be in bed by now

got back from the run i started this thread for a little before midnight. but;

will probably be doing something tonight (as in, wed 26/11) aswell, starting about 8-9. so if youre keen post here or send numbers via pm and start with the sms'ing. meet point will be sent to you and route will be kept off the forums.
Edited by scandyflick
PM sent :)

cheers. :)

I'd be keen, but I have a dinner tonight :)

it wont be starting til about 8, so if youre done by then and still keen, shoot me an sms and ill let you know whats up. ;)

i would have been down for the drive last night dave but you know i got soccer on

and as for tonight i dont know

might see you at villies though

no worries bud.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...