Jump to content
SAU Community

MeLz CruiZe Cruise - 23rd January 2009


Recommended Posts

lol you guys are funni

Nath, thanks for taking Benson and Co and yes I can't wait to see the sexifiro ;) lol my calaisturbo.com mates are all like "aww I don't want to get stickered cos of your ricer friends" and I'm like "ummm you gusy are half rice" lol jkz Nathan you might scare them haha

That's a shame the beast is away Scott, but yeah be good to meet you.

Just so you all know I won't have access AT ALL to the internet tomorrow so if you ned my mobile number for the cruise, pm me your email addy !!

Benson, are you able to keep an eye on the thread for me tomorrow and sms me if anyone needs anything? Cheers buddy!

Can't wait guys!

  • Replies 140
  • Created
  • Last Reply

Top Posters In This Topic

I'm hoping so ;) I had to have this weekend, last weekend was MV09 and next friday I want to go watch drift and I'm not keen on saturday cruising so yeah I hope it's a good turn out mym outh has gotten me into trouble in the past so I hope I can live up to it hahaha

just heard from takushi on sau cruise

apparently at first meet point at dogswamp, whole bunch of imports, then a little lebo guy in a vy ss rocks up, trys to do a skid, gets it out, flicks one way then flicks and grips and shoots him foward into a massive light post

hes so short that he misses airbag and smashes his head so theres blood everywhere, ambo and tow trcuk rock up, car is f##ked, and apparently his parents lived just across the road too

bulk pictures were taken, i cant wait

moral of story: dont do skids in a family car

pics? story from ppl there?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...