Jump to content
SAU Community

Recommended Posts

Item: Complete Rb26 Bottom end including sump if needed. (from R32)

Age: Most parts Brand new, crank used but crack tested.

Condition: All new parts with machining done (Almost at the stage of final assembly)

Price: Complete sell for $6000firm Note: value well over $7000

Willing to separate tho would rather sell together considering the work thats been done.

Location: Sydney

Value:

Cp pistons are +20 thou, well over $1000 new

Brand new Eagle rods $500+

N1 block is brand new item with machining, $2400 + machining work

Used tested cran $1000

acl bearings & arp main studs $200+

Rb26 sump + diff $500

+ the machining work $$$$

Comments:

Machining done as follows,

Hot tank Crank, Crack test crank,

Studs nuts fitted to main caps, Line hone 7 main's,

Rod check/set hone small end, rod check big end and align.

Tunnels measure sizes measure crush, check & set bearing clearances

Drill tap fit Plug

Comp spec micro polish crankshaft

Bore and Hone 6 cyl Torque plate

Trial build check deck and square

reface block square.

Balance 6 cyl manual.

Reason for sale, going to use my Mahle/Pauter rod combo instead

Edited by Angus Smart

Bump,

Would like to add all the work has been carried out by a very good shop in Adelaide Pm me if your interested to find out who.

good luck with that one buddy...

I've just checked the crank, dew to a few questions. it is the larger sized crank drive.

Cp pistons are 86.5mm (+20thou)

and going on what i can see, the ring gaps are the only thing left to be done +final assembly

  • 2 weeks later...
  • 2 weeks later...

Pistons and Rods are sold and there is no arp studs left

the rest is still up for sale

Block/Cradle, crank and bearings. will take 3400 for block and crank,

photos of block etc..

post-31456-1234266963_thumb.jpgpost-31456-1234267000_thumb.jpg

post-31456-1234267140_thumb.jpgpost-31456-1234267201_thumb.jpg

post-31456-1234267229_thumb.jpgpost-31456-1234267284_thumb.jpg

Pistons and Rods are sold and there is no arp studs left

the rest is still up for sale

Block/Cradle, crank and bearings. will take 3400 for block and crank,

photos of block etc..

post-31456-1234266963_thumb.jpgpost-31456-1234267000_thumb.jpg

post-31456-1234267140_thumb.jpgpost-31456-1234267201_thumb.jpg

post-31456-1234267229_thumb.jpgpost-31456-1234267284_thumb.jpg

Rods and pistons sold to me! Thanks Andrew!!!!

Andrew is a great guy to deal with guys!

Free bump!

  • 2 weeks later...

Block. crank cradle bearings still available.

Crank was rebuild/checked by Crankshaft rebuilders in Sa or Victoria.

Edited by Angus Smart
  • 2 weeks later...
Block. crank cradle bearings still available.

Crank was rebuild/checked by Crankshaft rebuilders in Sa or Victoria.

U willing to sell the cradle seperate if so message me. Cheers

  • 1 year later...
Block. crank cradle bearings still available.

Crank was rebuild/checked by Crankshaft rebuilders in Sa or Victoria.

i'm new to the forums so i can't send PMs yet.. do you have an e_mail where i can contact you?

i'm interested in the bearings

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...