Jump to content
SAU Community

Recommended Posts

S14 ganardor mirrors genuine electric painted black $350

S14 manual conversion kit:,used, flywheel, clutch, throw out, gearbox, shifter, speedo, abs tailshaft, clutch and brake pedals, master and slave, console $1000 $600 less gearbox

SR20 manual gearbox x2: 1xG/C $500 1xN/W 2nd gear synchro but has new bearings $400

SR20det s13 t25 off black top: good condition, manifold and dump, water lines $250

SR20 short shifter: ebay $50

S14 whiteline swaybars adj front and $50 refund on swap std bars $250

SR20 engine brace kit: bolts to strut tower $30

22OSX QLD number plates slim front, black w/- white $400

Braided oil line and oil pressure t- peice, brackets at rear of head suits sr20de+t conversion $100

SR20de+t s13 complete engine: turbo forged pistons, full balance, full reco head, bore & deck block, new lifters, 1.2mls head gasket, race brgs, gc flywheel, 5000kms $1500 $1800 inc. turbo and lines above.

Random other bits incl. s13 & s14 coils, s14 afm's, s14 ign module, s13 & s14 manual radiators & shrouds, complete s14 vct head, s14 single airbag dash, interior plastics, spare sr20 gearbox, s13 n/a short motor, booster and master cyls, std coolers & pipes, abs unit, a/c condensors, compressors and pipes, s14 rad support, jdm s14 rear bar OFFERS WELCOME

S14 sr20det series 1: jdm spec, uncut manual engine loom, coil packs, ign module, airflow, injectors, ecu, no coil pack loom or cas SOLD

S14 digital climate control kit: dash head unit, all sensors,actuators and looms SOLD

S13 sr20det: uncut manual engine loom, coil packs, cas, ign module, airflow, injectors, 2xecus SOLD

located gold coast

prefer pick up

postage at reasonable rates

txt Sam 0423 648 114

Edited by RED513
how much would it cost to post s14 manual conversion kit to melbourne?

couple of hundred as nearly 100kg

organize own courier is best

Edited by RED513

sr20de+t engine sold complete with turbo and braided line

rear bar no longer for sale, fitted to veh.

Would the S14 Manual gearbox conversion fit into S13 Silvia sr20DE engine?

and how much would it cost to be sent to Sydney?

Cheers!

most parts would fit, tailshaft would be different.

you would have to check.

perfer pickup as nearly 100kg and happy to put on grate, you organize courier.

Sam

whats the jdm rear bar look like? and is the g/c gearbox in working condition? Any whats the condition of the centre console?

rear bar has been painted and fitted, not for sale, No reflectors next to no. plate.

got 2x gearboxes, box in conversion kit good condition!, other box req 2nd syncro.

console has couple marks

Sam

S14 ignition module, vtc head, turbo SOLD

Edited by RED513

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...